气泡雾化喷嘴泡状流出口喷雾脉动特征

doi:10.11949/j.issn.0438-1157.20180647

化工学报 ›› 2018, Vol. 69 ›› Issue (10): 4253-4260.DOI: 10.11949/j.issn.0438-1157.20180647

气泡雾化喷嘴泡状流出口喷雾脉动特征

孙春华^1,2, 宁智¹, 乔信起², 李元绪¹, 吕明¹

1. 北京交通大学机械与电子控制工程学院, 北京 100044;
2. 上海交通大学内燃机研究所, 上海 200240

收稿日期:2018-06-12 修回日期:2018-07-30 出版日期:2018-10-05 发布日期:2018-10-05
通讯作者: 宁智
基金资助:
国家自然科学基金项目（51776016，51606006）；北京市自然科学基金项目（3172025）；国家重点研发计划项目（2017YFB0103401）。

Spray pulsating of effervescent atomizer operating in bubbly flow

SUN Chunhua^1,2, NING Zhi¹, QIAO Xinqi², LI Yuanxu¹, LÜ Ming¹

1. School of Mechanical, Electronic and Control Engineering, Beijing Jiaotong University, Beijing 100044, China;
2. Institute of Internal Combustion Engine, Shanghai Jiaotong University, Shanghai 200240, China

Received:2018-06-12 Revised:2018-07-30 Online:2018-10-05 Published:2018-10-05
Supported by:
supported by the National Natural Science Foundation of China (51776016, 51606006), the Natural Science Foundation of Beijing (3172025) and the National Key Research and Development Program of China (2017YFB0103401).

摘要/Abstract

摘要：

采用实验和仿真方法，对一特定气泡雾化喷嘴泡状流时混合室内的气液两相混合形态以及喷孔出口喷雾脉动特征进行了研究。研究结果表明，泡状流时气泡尺寸呈近似正态分布，气泡尺寸随液相质量流量和气液质量比增大而减小；喷雾形态和喷孔出口气液流动参数存在较大脉动，喷雾锥角脉动超过20°；气泡数量密度小且气泡直径较大时，喷雾平均锥角相对较小，且喷雾脉动现象比较严重；随着气泡数量密度增加，喷雾平均锥角呈现先快速增大后缓慢增大趋势，而喷雾锥角变异系数先快速增大随后逐渐减小并趋于稳定；复杂的流场结构是喷孔内气泡表观形态发生较大变化以及喷孔出口气液流动参数产生较大脉动的主要原因。

关键词: 气泡雾化喷嘴, 气泡, 气液两相流, 喷雾, 可视化, 模拟

Abstract:

The effervescent atomizer is a gas-liquid two-phase atomizer. Due to the discrete distribution of gas phase, the gas-liquid flow parameters at the atomizer exit fluctuate violently. In this study, characteristics of both bubbly flow pattern and spray pulsating characteristics were investigated by experimental and simulation methods. A visual effervescent spray system and a gas-liquid two-phase flow simulation model were established, and the operating conditions corresponding to bubbly flow were determined based on the gas-liquid flow regime map. The results show that the bubble size is approximately normal distribution in bubble flow, and the bubble size decreased with the increase of liquid mass flow rate and gas-liquid mass ratio. Under the same operation conditions, spray morphology and gas-liquid flow parameters at the exit orifice section at various times were observed with great difference, and the spray half cone angle varied larger than 10°. When the number density of bubbles was small and the bubble diameter was large at the same time, the spray cone angle was relatively small, and the spray pulsation was intense as well. With the increase of bubble number density, the average spray half cone angle showed a rapid increase followed by a slowly increasing trend, whereas the variation coefficient of the spray half cone angle increased rapidly first, then gradually decreased and tended to stable. Complex flow field structure was the main reason for the variation of bubble shape in the atomizer and the pulsation of gas-liquid flow parameters at the exit section of the atomizer.

Key words: effervescent atomizer, bubble, gas-liquid flow, spray, visualization, simulation

中图分类号:

O359⁺.1

孙春华, 宁智, 乔信起, 李元绪, 吕明. 气泡雾化喷嘴泡状流出口喷雾脉动特征[J]. 化工学报, 2018, 69(10): 4253-4260.

SUN Chunhua, NING Zhi, QIAO Xinqi, LI Yuanxu, LÜ Ming. Spray pulsating of effervescent atomizer operating in bubbly flow[J]. CIESC Journal, 2018, 69(10): 4253-4260.

参考文献 34

[1]	NASSER A. Handbook of Atomization and Sprays:Theory and Application[M]. New York:Springer Verlag, 2011.
[2]	KONSTANTINOV D, MARSH R, BOWEN P, et al. Effervescent atomization for industrial energy-technology review[J]. Atomization and Sprays, 2010, 10(6):525-552.
[3]	SOVANI S D, SOJKA P E, LEFEBVRE A H. Effervescent atomization[J]. Progress in Energy & Combustion Science, 2001, 27(4):483-521.
[4]	RASHKOVAN A, KHOLMER V, SHER E. Effervescent atomization of gasoline containing dissolved CO2[J]. Atomization and Sprays, 2004, 14(14):341-354.
[5]	QIAN L, LIN J, XIONG H. Simulation of droplet-gas flow in the effervescent atomization spray with an impinging plate[J]. Chinese Journal of Chemical Engineering, 2009, 17(1):8-19.
[6]	MAHRUKH M, KUMAR A, NABAVI S A, et al. Numerical analysis of the effects of using effervescent atomization on solution precursor thermal spraying process[J]. Industrial & Engineering Chemistry Research, 2017, 56(48):14231-14244.
[7]	MAHRUKH M, KUMAR A, GU S. Effects of angular injection, and effervescent atomization on high-velocity suspension flame spray process[J]. Surface & Coatings Technology, 2016, 302:368-382.
[8]	王锐, 周致富, 白飞龙, 等. R404a喷雾冷却表面传热特性的时空不均匀性[J]. 化工学报, 2015, 66(4):1258-1264. WANG R, ZHOU Z F, BAI F L, et al. Temporal and radial dependent profiles for surface heat transfer during R404a spray cooling[J]. CIESC Journal, 2015, 66(4):1258-1264.
[9]	SEN D, BALZAN M A, NOBES D S, et al. Bubble formation and flow instability in an effervescent atomizer[J]. Journal of Visualization, 2014, 17(2):113-122.
[10]	GHAFFAR Z A, KASOLANG S, HAMID A H A. Characteristics of swirl effervescent atomizer spray angle[J]. Applied Mechanics & Materials, 2014, 607:108-111.
[11]	JOBEHDAR M H, SIDDIQUI K, GADALLAH A H, et al. Effect of single-and multi-hole bubble breakers on the effervescent atomization process[J]. Atomization & Sprays, 2016, 26(2):135-162.
[12]	HONG M, FLECK B A, NOBES D S. Unsteadiness of the internal flow in an effervescent atomizer nozzle[J]. Experiments in Fluids, 2014, 55(12):1-15.
[13]	KOURMATZIS A, LOWE A, MASRI A R. Combined effervescent and airblast atomization of a liquid jet[J]. Experimental Thermal & Fluid Science, 2016, 75:66-76.
[14]	MLKVIK M, STAHLE P, SCHUCHMANN H P, et al. Twin-fluid atomization of viscous liquids:the effect of atomizer construction on breakup process, spray stability and droplet size[J]. International Journal of Multiphase Flow, 2015, 77:19-31.
[15]	WHITLOW J D, LEFEBVRE A H. Effervescent atomizer operation and spray characteristics[J]. Atomization and Sprays, 1993, 3(2):137-155.
[16]	BUSH S G, SOJKA P E. Entrainment by effervescent sprays at low mass flowrates[C]//Proceedings of the 6th ICLASS Conference. Rouen, 1994.
[17]	CHIN J S, LEFEBVRE A H. Design procedure for effervescent atomizers[J]. ASME Transaction Journal of Engineering for Gas Turbines and Power, 1995, 117(2):266-271.
[18]	ROESLER T C, LEFEBVRE A H. Photographic studies on aerated-liquid atomization, combustion fundamentals and applications[C]//Proceedings of the Central States Section of the Combustion Institute Meeting. Indianapolis, 1988.
[19]	CHEN S K, LEFEBVRE A H. Discharge coefficients for plain-orifice effervescent atomizers[J]. Atomization and Sprays, 1994, 4(3):275-290.
[20]	JEDELSKY J, JICHA M. Characteristics of a two-phase flow inside the mixing chamber of an effervescent atomizer[C]//Proceedings of the 3rd International Symposium on Two-Phase Flow Modelling and Experimentation. Pisa, 2004.
[21]	刘联胜. 气泡雾化喷嘴的雾化特性及其喷雾两相流场的实验与理论研究[D]. 天津:天津大学, 2001. LIU L S. Experimental and theoretical studies on the spray characteristics and two-phase spray field of effervescent atomizers[D]. Tianjin:Tianjin University, 2001.
[22]	LUONG J T K. Unsteadiness in effervescent sprays[J]. Atomization and Sprays, 1999, 9(1):87-109.
[23]	JEDELSKY J, BEINSTEIN Z, JICHA M. Unsteadiness in effervescent sprays:influence of operational conditions and atomizer design[C]//Proceedings of the 11st ICLASS Conference.Vail, 2009.
[24]	LIU M, DUAN Y F, ZHANG T N. Evaluation of unsteadiness in effervescent sprays by analysis of droplet arrival statistics-the influence of fluids properties and atomizer internal design[J]. Experimental Thermal and Fluid Science, 2011, 35(1):190-198.
[25]	刘猛, 段钰锋, 张铁男, 等. 液体性质对气泡雾化液滴不稳定性的影响[J]. 东南大学学报(自然科学版), 2012, 42(2):295-300. LIU M, DUAN Y, ZHANG T, et al. Influence of liquids properties on unsteadiness of droplet in effervescent sprays[J]. Journal of Southeast University (English Edition), 2012, 42(2):295-300.
[26]	LIN K C, KENNEDY P J, JACKSON T A. Structures of internal flow and the corresponding spray for aerated-liquid injectors[C]//37th AIAA/ASME/SAE/ASEE Joint Prop.lsion Conference, Salt Lake City, 2001.
[27]	MALDONADO S, FLECK B A, HEIDRICK T, et al. Development of an experimental method to evaluate the stability of gas-liquid sprays[J]. Atomization and Sprays, 2008, 18(8):699-722.
[28]	刘联胜, 吴晋湘, 傅茂林, 等. 气泡雾化喷嘴雾化特性实验[J]. 燃烧科学与技术, 2001, 7(1):63-64. LIU L S, WU J X, FU M L, et al. Experimental studies on the spray characteristics of effervescent atomizers[J]. Journal of Combustion Science & Technology, 2001, 7(1):63-64.
[29]	ZAREMBA M, MALY M, JEDELSKY J, et al. An experimental analysis of the spraying processes in improved design of effervescent atomizer[J]. International Journal of Multiphase Flow, 2018, 103:1-15.
[30]	刘联胜, 傅茂林, 王海, 等. 气泡雾化喷嘴流量特性的实验研究[J]. 燃烧科学与技术, 1999, 5(3):297-303. LIU L S, FU M L, WANG H, et al. Experimental studies on the flow rate characteristic of effervescent atomizers[J]. Journal of Combustion Science & Technology, 1999, 5(3):297-303.
[31]	HUANG X, WANG X, LIAO G. Visualization of two phase flow inside an effervescent atomizer[J]. Journal of Visualization, 2008, 11(4):299-308.
[32]	孙春华. 气泡雾化喷射中气液两相作用及射流喷雾的研究[D]. 北京:北京交通大学, 2018. SUN C H. Study on interactions between gas liquid two phases and jet spray in effervescent sprays[D]. Beijing:Beijing Jiaotong University, 2018.
[33]	BYAKOVA A V. Influence of wetting conditions on bubble formation at orifice in an inviscid liquid[J]. Transformation of Bubble Shape and Size, Colloids and Surfaces A:Physicochem, 2003, 218(1):73-87.
[34]	LORCHER M, SCHMIDT F, MEWES D. Effervescent atomization of liquids[J]. Atomization and Sprays, 2005, 15(2):145-168.

气泡雾化喷嘴泡状流出口喷雾脉动特征

Spray pulsating of effervescent atomizer operating in bubbly flow

PDF (PC)

可视化

被引次数

摘要/Abstract

引用本文

使用本文

参考文献 34

相关文章 15

编辑推荐

Metrics

本文评价

[1]	宋嘉豪, 王文. 斯特林发动机与高温热管耦合运行特性研究[J]. 化工学报, 2023, 74(S1): 287-294.
[2]	张思雨, 殷勇高, 贾鹏琦, 叶威. 双U型地埋管群跨季节蓄热特性研究[J]. 化工学报, 2023, 74(S1): 295-301.
[3]	肖明堃, 杨光, 黄永华, 吴静怡. 浸没孔液氧气泡动力学数值研究[J]. 化工学报, 2023, 74(S1): 87-95.
[4]	叶展羽, 山訸, 徐震原. 用于太阳能蒸发的折纸式蒸发器性能仿真[J]. 化工学报, 2023, 74(S1): 132-140.
[5]	邵苛苛, 宋孟杰, 江正勇, 张旋, 张龙, 高润淼, 甄泽康. 水平方向上冰中受陷气泡形成和分布实验研究[J]. 化工学报, 2023, 74(S1): 161-164.
[6]	张龙, 宋孟杰, 邵苛苛, 张旋, 沈俊, 高润淼, 甄泽康, 江正勇. 管翅式换热器迎风侧翅片末端霜层生长模拟研究[J]. 化工学报, 2023, 74(S1): 179-182.
[7]	张义飞, 刘舫辰, 张双星, 杜文静. 超临界二氧化碳用印刷电路板式换热器性能分析[J]. 化工学报, 2023, 74(S1): 183-190.
[8]	王志国, 薛孟, 董芋双, 张田震, 秦晓凯, 韩强. 基于裂隙粗糙性表征方法的地热岩体热流耦合数值模拟与分析[J]. 化工学报, 2023, 74(S1): 223-234.
[9]	江河, 袁俊飞, 王林, 邢谷雨. 均流腔结构对微细通道内相变流动特性影响的实验研究[J]. 化工学报, 2023, 74(S1): 235-244.
[10]	陈哲文, 魏俊杰, 张玉明. 超临界水煤气化耦合SOFC发电系统集成及其能量转化机制[J]. 化工学报, 2023, 74(9): 3888-3902.
[11]	宋明昊, 赵霏, 刘淑晴, 李国选, 杨声, 雷志刚. 离子液体脱除模拟油中挥发酚的多尺度模拟与研究[J]. 化工学报, 2023, 74(9): 3654-3664.
[12]	袁佳琦, 刘政, 黄锐, 张乐福, 贺登辉. 泡状入流条件下旋流泵能量转换特性研究[J]. 化工学报, 2023, 74(9): 3807-3820.
[13]	胡建波, 刘洪超, 胡齐, 黄美英, 宋先雨, 赵双良. 有机笼跨细胞膜易位行为的分子动力学模拟研究[J]. 化工学报, 2023, 74(9): 3756-3765.
[14]	赵佳佳, 田世祥, 李鹏, 谢洪高. SiO₂-H₂O纳米流体强化煤尘润湿性的微观机理研究[J]. 化工学报, 2023, 74(9): 3931-3945.
[15]	何松, 刘乔迈, 谢广烁, 王斯民, 肖娟. 高浓度水煤浆管道气膜减阻两相流模拟及代理辅助优化[J]. 化工学报, 2023, 74(9): 3766-3774.