树脂基热防护材料烧蚀传热的关键参数影响性分析

doi:10.11949/j.issn.0438-1157.20170635

摘要/Abstract

摘要：

针对树脂基热防护材料烧蚀传热的关键参数分析问题，采用碳化层-热解层-原始材料层一维模型，分析了热防护材料烧蚀热解响应过程的传热特性，得出了不确定参数影响传热过程的敏感性大小，结果表明：材料的热导率对树脂基热防护材料烧蚀传热特性影响最大，密度、比热容和材料厚度影响程度较大，其他参数的影响性可以忽略。同时建立了温度和不确定参数之间的量纲1准则关系式，为热防护材料的选取设计以及模型参数修正提供了参考依据。

关键词: 数值分析, 热解, 传热, 敏感性分析

Abstract:

To analysis the key parameters of ablation heat transfer resin based thermal protection materials, a charring layer-pyrolysis layer-original material layer one-dimensional model is applied, heat transfer process is analyzed, and the uncertain parameters sensitivity of ablative heat response of thermal protection material is obtained. The results show that the thermal conductivity is the greatest impact on the heat transfer characteristics of resin based thermal protection material ablation, the density, specific heat capacity and material thickness are secondary, and the influence of other parameters can be ignored. Meanwhile, the dimensionless correlation between the temperature and the uncertain parameters is established, which provides a reference for the selection, design and parameters correction of the thermal protection materials.

Key words: numerical analysis, pyrolysis, heat transfer, sensitivity analysis

中图分类号:

V435⁺.14

王潇敏, 程文龙, 张利嵩, 刘娜. 树脂基热防护材料烧蚀传热的关键参数影响性分析[J]. 化工学报, 2018, 69(4): 1385-1390.

WANG Xiaomin, CHENG Wenlong, ZHANG Lisong, LIU Na. Analysis of influence of key parameters on ablative heat transfer of resin based thermal protection material[J]. CIESC Journal, 2018, 69(4): 1385-1390.

参考文献 31

[1]	张志成. 高超声速气动热和热防护[M]. 北京:国防工业出版社, 2003:222-317. ZHANG Z C. Hypersonic Aerodynamic Heat and Thermal Protection[M]. Beijing:National Defense Industry Press, 2003:222-317.
[2]	张涛. 热解气体流动的二维烧蚀热防护数值仿真研究[J]. 宇航学报, 2014, 35(1):119-124. ZHANG T. Numerical simulation research on two-dimensional ablative thermal protection with pyrolysis gas flow[J]. Journal of Astronautics, 2014, 35(1):119-124.
[3]	刘骁, 国义军, 刘伟, 等. 碳化材料三维烧蚀热响应有限元计算研究[J]. 宇航学报, 2016, 37(9):1150-1156. LIU X, GUO Y J, LIU W, et al. Numerical simulation research on three-dimensional ablative thermal response of charring ablators[J]. Journal of Astronautics, 2016, 37(9):1150-1156.
[4]	BAHRAMIAN A R, KOKABI M, FAMILI M H N, et al. Ablation and thermal degradation behaviour of a composite based on resol type phenolic resin:process modeling and experimental[J]. Polymer, 2006, 47(10):3661-3673.
[5]	HAKKAKI F A, KOWSARY F. Heat flux estimation in a charring ablator[J]. Numerical Heat Transfer, Part A:Applications, 2007, 53(5):543-560.
[6]	XU Y H, HU X, YANG Y X, et al. Dynamic simulation of insulation material ablation process in solid propellant rocket motor[J]. Journal of Aerospace Engineering, 2014, 28(5):04014118.
[7]	ALBA C R, GREENDYKE R B. Nonequilibrium finite-rate carbon ablation model for earth reentry flows[J]. Journal of Spacecraft and Rockets, 2016, 53(3):579-583.
[8]	LI W J, HUANG H M, TIAN Y, et al. A nonlinear pyrolysis layer model for analyzing thermal behavior of charring ablator[J]. International Journal of Thermal Sciences, 2015, 98:104-112.
[9]	LI W J, HUANG H M, TIAN Y, et al. Nonlinear analysis on thermal behavior of charring materials with surface ablation[J]. International Journal of Heat and Mass Transfer, 2015, 84:245-252.
[10]	HUANG H M, LI W J, YU H L. Thermal analysis of charring materials based on pyrolysis interface model[J]. Thermal Science, 2014, 18(5):1591-1596.
[11]	LI W J, HUANG H M, AI B C, et al. On the novel designs of charring composites for thermal protection application in reentry vehicles[J]. Applied Thermal Engineering, 2016, 93:849-855.
[12]	GORI F, CORASANITI S, WOREK W M, et al. Theoretical prediction of thermal conductivity for thermal protection systems[J]. Applied Thermal Engineering, 2012, 49:124-130.
[13]	EWING M E, LAKER T S, WALKER D T. Numerical modeling of ablation heat transfer[J]. Journal of Thermophysics and Heat Transfer, 2013, 27(4):615-632.
[14]	LACHAUD J, MAGIN T E, COZMUTA I, et al. A short review of ablative-material response models and simulation tools[C]//7th Aerothermodynamics Symposium. Belgium:European Space Agency, 2011.
[15]	WENG H Y, MARTIN A. Numerical investigation of thermal response using orthotropic charring ablative material[J]. Journal of Thermophysics and Heat Transfer, 2015, 29(3):429-438
[16]	AMAR A J. Modeling of One-dimensional Ablation with Porous Flow Using Finite Control Volume Procedure[M]. Raleigh:North Carolina State University, 2006:12-134.
[17]	WENG H Y, MARTIN A. Multidimensional modeling of pyrolysis gas transport inside charring ablative materials[J]. Journal of Thermophysics and Heat Transfer, 2014, 28(4):583-597.
[18]	LACHUAD J, VAN EEKELEN T, SCOGGINS J B, et al. Detailed chemical equilibrium model for porous ablative materials[J]. International Journal of Heat and Mass Transfer, 2015, 90:1034-1045.
[19]	LI W J, HUANG H M, YU H L, et al. Effects of gradient density on effective heat capacity of charring ablative material for re-entry vehicles[J]. International Journal of Numerical Methods for Heat & Fluid Flow, 2015, 25(3):472-483.
[20]	LI W J, HUANG H M, WANG Q, et al. Protection of pyrolysis gases combustion against charring materials' surface ablation[J]. International Journal of Heat and Mass Transfer, 2016, 102:10-17.
[21]	CHEN Y K, MILOS F S. Effects of nonequilibrium chemistry and Darcy-Forchheimer pyrolysis flow for charring ablator[J]. Journal of Spacecraft and Rockets, 2013, 50(2):256-269
[22]	GHORBANI Z, WEBSTER R, LAZARO M, et al. Critical evaluation of parameter estimation techniques for pyrolysis of charring materials[C]//8th US National Combustion Meeting. Utah:Western States Section of the Combustion Institute, 2013.
[23]	CHEN Y K, SQUIRE T, LAUB B, et al. Monte Carlo analysis for spacecraft thermal protection system design[C]//9th AIAA/ASME Joint Thermophysics and Heat Transfer Conference. San Francisco, 2006.
[24]	CHEN Y K, MILOS F S, GOKEEN T. Validation of a three-dimensional ablation and thermal response simulation code[C]//10th AIAA/ASME Joint Thermophysics and Heat Transfer Conference. Chicago, 2010.
[25]	刘军. 科学计算中的蒙特卡罗策略[M]. 北京:高等教育出版社, 2009:17-38. LIU J. Monte Carlo Strategies in Scientific Computing[M]. Beijing:Higher Education Press, 2009:17-38.
[26]	CHENG W L, LIU N, LI Z, et al. Application study of a correction method for a spacecraft thermal model with a Monte Carlo hybrid algorithm[J]. Chinese Science Bulletin, 2011, 56(13):1407-1412.
[27]	BLACKWELL B F. Numerical prediction of one-dimensional ablation using a finite control volume procedure with exponential differencing[J]. Numerical Heat Transfer, Part A:Applications, 1988, 14(1):17-34.
[28]	AMAR A J, BLACKWELL B F, EDWARDS J R. One-dimensional ablation using a full Newton's method and finite control volume procedure[J]. Journal of Thermophysics and Heat Transfer, 2008, 22(1):71-82.
[29]	AMAR A J, BLACKWELL B F, EDWARDS J R. Development and verification of a one-dimensional ablation code including pyrolysis gas flow[J]. Journal of Thermophysics and Heat Transfer, 2009, 23(1):59-71.
[30]	LACHAUD J, MARTIN A, COZMUTA I, et al. Ablation Workshop Test Case[EB/OL]. 2011
	[2017] . http://ablation 2012. engineering. uky.edu/files/2012/02/Test_Case_1. pdf.
[31]	于翘. 材料工艺. 下[M]. 北京:中国宇航出版社, 1989:10-192. YU Q. Material Technology, Part B[M]. Beijing:China Astronautic Publishing House, 1989:10-192.