水性聚氨酯的结晶动力学参数及其在鞋用胶黏剂的应用

doi:10.3969/j.issn.0438-1157.2014.04.047

化工学报 ›› 2014, Vol. 65 ›› Issue (4): 1503-1508.DOI: 10.3969/j.issn.0438-1157.2014.04.047

• 材料化学工程与纳米技术 • 上一篇下一篇

水性聚氨酯的结晶动力学参数及其在鞋用胶黏剂的应用

曹高华, 夏正斌, 雷亮, 张燕红

华南理工大学化学与化工学院, 广东广州 510640

收稿日期:2013-07-08 修回日期:2013-08-12 出版日期:2014-04-05 发布日期:2013-11-27
通讯作者: 夏正斌
作者简介:曹高华（1988—）, 男, 硕士研究生。
基金资助:
省部企业科技特派员行动计划合作项目（TPY 2010031549660）。

Crystallization kinetics parameters of waterborne polyurethane and its application in adhesive for shoes

CAO Gaohua, XIA Zhengbin, LEI Liang, ZHANG Yanhong

School of Chemistry and Chemical Engineering, South China University of Technology, Guangzhou 510640, Guangdong, China

Received:2013-07-08 Revised:2013-08-12 Online:2014-04-05 Published:2013-11-27

摘要/Abstract

摘要： 以聚己二酸1，4-丁二醇酯（PBA）、六亚甲基二异氰酸酯（HDI）和异佛尔酮二异氰酸酯（IPDI）为主要原料，制备了不同软段分子量和不同硬段含量的水性聚氨酯（WPU）乳液。采用DSC技术表征了WPU胶膜在非等温和等温条件下的结晶行为，并以莫志深方程和Avrami方程为模型，对WPU胶膜的结晶行为进行了研究。WPU胶膜的非等温结晶动力学分析结果表明，随着WPU相对结晶度的增加，非等温结晶动力学参数F（T）增大，说明适当提高活化温度可提高WPU胶黏剂的结晶速率和初黏强度；WPU胶膜的等温动力学分析结果表明，不同软段分子量和不同硬段含量的WPU胶膜的等温结晶动力学参数t_1/2与相应WPU胶黏剂的开放时间存在对应关系，即t_1/2较大者，相应WPU胶黏剂的开放时间较长。

关键词: 聚合物, 水性聚氨酯, 结晶, 动力学, 胶黏剂, 初黏强度, 开放时间

Abstract: Waterborne polyurethane (WPU) dispersions with different molecular weights of soft segment and different contents of hard segment were synthesized by using polyethylene glycol adipate diol (PBA), isophorone diisocyanate (IPDI), hexamethylene diisocyanate (HDI) as the main raw materials. The crystallization behavior of WPU films under isothermal and non-isothermal conditions were characterized by DSC, and their crystallization kinetics were investigated by Avrami equation and Mo Zhishen equation, respectively. The non-isothermal crystallization kinetics results showed that the non-isothermal crystallization kinetics parameters F(T) increased with the increase of relative crystallinity, which suggested that enhancement of activation temperature could improve the crystallization rate and initial bonding strength of WPU adhesive. The isothermal crystallization kinetics results indicated that a correspondence could be found between isothermal crystallization kinetics parameters t_1/2 of WPU films and the open time of WPU adhesive. The larger the t_1/2 of WPU films was, the longer the open time of WPU adhesive would have.

Key words: polymers, waterborne polyurethane, crystallization, kinetics, adhesive, initial bonding strength, open time

中图分类号:

曹高华, 夏正斌, 雷亮, 张燕红. 水性聚氨酯的结晶动力学参数及其在鞋用胶黏剂的应用[J]. 化工学报, 2014, 65(4): 1503-1508.

CAO Gaohua, XIA Zhengbin, LEI Liang, ZHANG Yanhong. Crystallization kinetics parameters of waterborne polyurethane and its application in adhesive for shoes[J]. CIESC Journal, 2014, 65(4): 1503-1508.

参考文献

[1] Tardif X, Agazzi A, Sobotka V, Boyard N, Jarny Y, Delaunay D. A multifunctional device to determine specific volume, thermal conductivity and crystallization kinetics of semi-crystalline polymers[J]. Polymer Testing, 2012, 31(6): 819-827
[2] Weng M T, Qiu Z B. Crystallization kinetics and morphology of novel miscible crystalline/amorphous polymer blends of biodegradable poly(butylene succinate-co-butylene carbonate) and poly(vinyl phenol)[J]. Industrial and Engineering Chemistry Research, 2013, 52(30): 10198-10205
[3] Zendehzaban M, Shamsipur M. Isothermal crystallization kinetics of poly(ethylene terephthalate)s of different molecular weights[J]. Journal of the Iranian Chemical Society, 2013, 10(1): 77-84
[4] Rong Yan(荣彦), He Huiping(贺惠萍), Cao Wei(曹伟), Shen Changyu(申长雨), Chen Jingbo(陈静波). Numerical simulation of flow-induced crystallization of polymer based on two-phase model[J]. CIESC Journal (化工学报), 2012, 63(7): 2252-2257
[5] Jeziorny A. Parameters characterizing the kinetics of the non-isothermal crystallization of poly(ethylene terephthalate) determined by DSC[J]. Polymer, 1978, 19(10): 1142-1144
[6] Ozawa T. Kinetics of non-isothermal crystallization[J]. Polymer, 1970, 12(3): 150-158
[7] Dutta A. Method to obtain Avrami parameters directly from nonisothermal crystallization data[J]. Polymer Communications, 1990, 31(12): 451-452
[8] Kissinger H E. Reaction kinetics in differential thermal analysis[J]. Analytical Chemistry, 1957, 29(11): 1702-1706
[9] Avrami M. Kinetics of phase change(Ⅰ): General theory[J]. Journal of Chemical Physics, 1939, 7(12): 1103-1113
[10] Mo Zhishen(莫志深). A method for the non-isothermal crystallization kinetics of polymers[J]. Acta Polymerica Sinica (高分子学报), 2008(7): 656-661
[11] Wu F, Li Y J, Chen R J, Chen S. Preparation and characterization of a mixing soft-segment waterborne polyurethane polymer electrolyte[J]. Chinese Chemical Letters, 2009, 20(1): 115-118
[12] Liu X, Xu K, Liu H, Cai H L, Su J X, Fu Z, Guo Y, Chen M C. Preparation and properties of waterborne polyurethanes with natural dimer fatty acids based polyester polyol as soft segment[J]. Progress in Organic Coatings, 2011, 72(4): 612-620
[13] Begenir A, Michielsen S, Pourdeyhimi B. Melt-blowing thermoplastic polyurethane and polyether-block- amide elastomers: effect of processing conditions and crystallization on web properties[J]. Polymer Engineering and Science, 2009, 49(7): 1340-1349
[14] Cao Gaohua(曹高华), Xia Zhengbin(夏正斌), Zhang Yanhong(张燕红), Li Wei(李伟). Effects of AAS/DMPA on crystallinity of films of waterborne polyurethane[J]. CIESC Journal (化工学报), 2013, 64(7): 2672-2678
[15] Liu Jieping(刘结平), Mo Zhishen(莫志深).Crystallization kinetics of polymers[J]. Polymer Bulletin(高分子通报), 1991(4): 199-207
[16] Qiao X, Wang X, Zhao X, Mo Z S, Zhang H. Nonisothermal crystallization of poly(3- dodecylthiophene) and poly(3-octadecylthiophene) [J]. Synthetic Metals, 2000, 113(1): 1-6
[17] Johnson W A, Mehl R F. Reaction kinetics in processes of nucleation and growth[J]. Transactions of the American Institute of Mining and Metallurgical Engineers, 1939, 135: 416-442
[18] Avrami M. Granulation, phase change, and microstructure kinetics of phase change. Ⅲ[J]. Journal of Chemical Physics, 1941, 9(2): 177l-184
[19] Avrami M. Kinetics of phase change(Ⅱ): Transformation-time relations for random distribution of nuclei[J]. Journal of Chemical Physics, 1941, 8(21): 212-224
[20] Evans U R. The laws of expanding circles and spheres in relation to the lateral growth of surface films and the grain-size of metals[J]. Transactions of the Faraday Society, 1945, 41: 365-374
[21] Zhu Y, Hu J L, Yeung K W, Liu Y Q, Liem H M. Influence of ionic groups on the crystallization and melting behavior of segmented polyurethane ionomers[J]. Journal of Applied Polymer Science, 2006, 100(6): 4603-4613

水性聚氨酯的结晶动力学参数及其在鞋用胶黏剂的应用

Crystallization kinetics parameters of waterborne polyurethane and its application in adhesive for shoes

PDF (PC)

可视化

被引次数

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	毕丽森, 刘斌, 胡恒祥, 曾涛, 李卓睿, 宋健飞, 吴翰铭. 粗糙界面上纳米液滴蒸发模式的分子动力学研究[J]. 化工学报, 2023, 74(S1): 172-178.
[2]	于宏鑫, 邵双全. 水结晶过程的分子动力学模拟分析[J]. 化工学报, 2023, 74(S1): 250-258.
[3]	金正浩, 封立杰, 李舒宏. 氨水溶液交叉型再吸收式热泵的能量及分析[J]. 化工学报, 2023, 74(S1): 53-63.
[4]	程成, 段钟弟, 孙浩然, 胡海涛, 薛鸿祥. 表面微结构对析晶沉积特性影响的格子Boltzmann模拟[J]. 化工学报, 2023, 74(S1): 74-86.
[5]	肖明堃, 杨光, 黄永华, 吴静怡. 浸没孔液氧气泡动力学数值研究[J]. 化工学报, 2023, 74(S1): 87-95.
[6]	范孝雄, 郝丽芳, 范垂钢, 李松庚. LaMnO₃/生物炭催化剂低温NH₃-SCR催化脱硝性能研究[J]. 化工学报, 2023, 74(9): 3821-3830.
[7]	郑佳丽, 李志会, 赵新强, 王延吉. 离子液体催化合成2-氰基呋喃反应动力学研究[J]. 化工学报, 2023, 74(9): 3708-3715.
[8]	汪林正, 陆俞冰, 张睿智, 罗永浩. 基于分子动力学模拟的VOCs热氧化特性分析[J]. 化工学报, 2023, 74(8): 3242-3255.
[9]	杨越, 张丹, 郑巨淦, 涂茂萍, 杨庆忠. NaCl水溶液喷射闪蒸-掺混蒸发的实验研究[J]. 化工学报, 2023, 74(8): 3279-3291.
[10]	傅予, 刘兴翀, 王瀚雨, 李海敏, 倪亚飞, 邹文静, 雷月, 彭永姗. F₃EACl修饰层对钙钛矿太阳能电池性能提升的研究[J]. 化工学报, 2023, 74(8): 3554-3563.
[11]	曾如宾, 沈中杰, 梁钦锋, 许建良, 代正华, 刘海峰. 基于分子动力学模拟的Fe₂O₃纳米颗粒烧结机制研究[J]. 化工学报, 2023, 74(8): 3353-3365.
[12]	李锦潼, 邱顺, 孙文寿. 煤浆法烟气脱硫中草酸和紫外线强化煤砷浸出过程[J]. 化工学报, 2023, 74(8): 3522-3532.
[13]	王杰, 丘晓琳, 赵烨, 刘鑫洋, 韩忠强, 许雍, 蒋文瀚. 聚电解质静电沉积改性PHBV抗氧化膜的制备与性能研究[J]. 化工学报, 2023, 74(7): 3068-3078.
[14]	刘杰, 吴立盛, 李锦锦, 罗正鸿, 周寅宁. 含乙烯基胺酯键聚醚类可逆交联聚合物的制备及性能研究[J]. 化工学报, 2023, 74(7): 3051-3057.
[15]	张蒙蒙, 颜冬, 沈永峰, 李文翠. 电解液类型对双离子电池阴阳离子储存行为的影响[J]. 化工学报, 2023, 74(7): 3116-3126.