气泡微细化沸腾过程中气泡冷凝破裂现象

doi:10.3969/j.issn.0438-1157.2014.08.007

化工学报 ›› 2014, Vol. 65 ›› Issue (8): 2902-2907.DOI: 10.3969/j.issn.0438-1157.2014.08.007

气泡微细化沸腾过程中气泡冷凝破裂现象

唐继国¹, 阎昌琪¹, 孙立成², 朱光昱¹

1 哈尔滨工程大学核安全与仿真技术国防重点学科实验室, 黑龙江哈尔滨 150001;
2 四川大学水利水电学院, 四川成都 610207

收稿日期:2013-11-15 修回日期:2013-12-16 出版日期:2014-08-05 发布日期:2014-08-05
通讯作者: 阎昌琪
基金资助:
国家自然科学基金项目（51376052）；教育部中央高校科研专项基金（HEUCFZ1122）；教育部留学归国人员科研启动基金项目。

Condensation and collapse of bubbles in region of microbubble emission boiling

TANG Jiguo¹, YAN Changqi¹, SUN Licheng², ZHU Guangyu¹

1 Fundamental Science on Nuclear Safety and Simulation Technology Laboratory, Harbin Engineering University, Harbin 150001, Heilongjiang, China;
2 College of Hydraulic and Hydra-electric Engineering, Sichuan University, Chengdu 610207, Sichuan, China

Received:2013-11-15 Revised:2013-12-16 Online:2014-08-05 Published:2014-08-05
Supported by:
supported by the National Natural Science Foundation of China (51376052), the Fundamental Research Funds for the Central Universities (HEUCFZ1122) and SRF for ROCS, SEM.

摘要/Abstract

摘要： 为了研究气泡微细化沸腾（MEB）时的气泡动力学行为，利用高速摄像仪（Fastcam SA5）观察15～60 K过冷度范围内，直径10 mm加热面上的沸腾过程。通过引入等效半径，分析核态沸腾、膜态沸腾和MEB区域的气泡行为特征。结果表明：MEB发生时的气泡行为，既不同于核态沸腾，也与膜态沸腾明显不同。在MEB区域，加热面上通常会形成一个大的、不规则气泡，但并不会脱离加热面，而是迅速破碎凝结；而且气泡生命周期相对较小，体积变化速率更快。量纲1分析发现，在MEB区域，随着壁面过热度和热通量的升高，气泡凝缩破裂过程受惯性控制影响程度逐渐增加。

关键词: 气泡微细化沸腾, 气泡行为, 凝结, 传热, 两相流

Abstract: To illustrate the bubble dynamics in microbubble emission boiling (MEB), a high-speed video camera (Fastcam SA5) was employed to observe the boiling phenomena on a heating surface with a diameter of 10 mm at the liquid subcooling of 15-60 K. An equivalent radius was induced to analyze the bubble behavior in different boiling regions. It is showed that the bubble behavior of MEB differs from that of nucleate boiling and film boiling obviously. In the regime of MEB, a large irregular bubble commonly forms on the heating surface and collapses immediately, but not departures from the heating surface. The period of bubble ebullition is shorter, with a faster change rate in volume. A dimensionless analysis shows that the inertia control increasingly dominates the process of bubble collapse with the increase of wall superheat and heat flux.

Key words: microbubble emission boiling, bubble behavior, condensation, heat transfer, two-phase flow

中图分类号:

TK124

唐继国, 阎昌琪, 孙立成, 朱光昱. 气泡微细化沸腾过程中气泡冷凝破裂现象[J]. 化工学报, 2014, 65(8): 2902-2907.

TANG Jiguo, YAN Changqi, SUN Licheng, ZHU Guangyu. Condensation and collapse of bubbles in region of microbubble emission boiling[J]. CIESC Journal, 2014, 65(8): 2902-2907.

参考文献 25

[1]	Inada S, Miyasaka Y, Izumi R, Owase Y. A study on boiling curves in subcooled pool boiling (Ⅰ): An effect of liquid subcooling on local heat transfer [J]. Transaction of JSME, 1981, 47 (417): 852-861
[2]	Inada S, Miyasaka Y, Sakumoto S, Izumi R. A study on boiling curves in subcooled pool boiling (Ⅱ): Effect of contamination of surface on boiling heat transfer and collapse vapor slug [J]. Transaction of JSME, 1981, 47 (422): 2021-2029
[3]	Inada S, Miyasaka Y, Izumi R. A study on boiling curves in subcooled pool boiling (Ⅲ): Behaviors of bubble cluster and temperature fluctuations of heating surface [J]. Transaction of JSME, 1981, 47 (422): 2030-2041
[4]	Inada S, Miyasaka Y, Izumi R. A study on boiling curves in subcooled pool boiling (Ⅳ): Heat transfer mechanism in transition boiling [J]. Transaction of JSME, 1981, 47(423): 2199-2208
[5]	Suzuki K, Torikai K, Satoh H, Ishimaru J, Tanaka Y. Boiling heat transfer of subcooled water in a horizontal rectangular channel: observation of MEB and MEB generation [J]. Heat Transfer Asian Research, 2001, 30: 426-438
[6]	Suzuki K, Saitoh H, Matsumoto K. High heat flux cooling by microbubble emission boiling [J]. Annuals of the New York Academy of Sciences, 2002, 974: 364-377
[7]	Suzuki K, Kokubu T, Nakano M, Kawamura H, Ueno I, Shida H, Ogawa O. Enhancement of heat transfer in subcooled flow boiling with microbubble emission [J]. Experimental Thermal and Fluid Science, 2005, 29: 827-832
[8]	Suzuki K, Nomura T, Hong C, Yuki K. Subcooled flow boiling with microbubble emission in a microchannel//Proceedings the MNHMT 2009 [C]. Shanghai, 2009
[9]	Suzuki K, Nakano H, Itoh M. Subcooled boiling of aqueous solution of alcohols//Proceedings of the 6th KSME-JSME Thermal and Fluid Engineering Conference [C]. 2005
[10]	Wang G D, Cheng P. Subcooled flow boiling and microbubble emission boiling phenomena in a partially heated microchannel [J]. International Journal of Heat and Mass Transfer, 2009, 52: 79-91
[11]	Ueno I, Arima M. Behavior of vapor bubble in subcooled pool [J]. International Journal for Microgravity Research and Applications, 2007, 3: 128-129
[12]	Ueno I, Hattori Y. Microbubble formation in abrupt condensation of vapor bubble exposed to subcooled pool//Proceedings of the InterPACK'09 [C]. Shanghai, 2009
[13]	Ueno I, Hattori Y, Hosoya R. Condensation and collapse of vapor bubbles injected in subcooled pool [J]. Microgravity Science and Technology, 2011, 23: 73-77
[14]	Shoji M, Yoshihara M. Burnout heat flux of water on a thin wire//Proceedings of 28th National Heat Transfer Symposium of Japan [C]. Japan, 1991: 121-123
[15]	Tange M, Takagi S, Watanabe M, Shoji M. Microbubble emission boiling in a microchannel and minichannel [J]. Thermal Sciences Engineering, 2004, 12: 23-29
[16]	Zeigarnik Yu A, Platonov D N, Khodakov K A, Shekhter Yu L. Visualization of boiling of subcooled water [J]. High Temperature, 2011, 49 (4): 566-570
[17]	Zeigarnik Yu A, Platonov D N, Khodakov K A, Shekhter Yu L. The nature of microbubble emission under subcooled water boiling [J]. High Temperature, 2012, 50 (3): 78-83
[18]	Tang J G, Zhu G Y, Sun L C. Microbubble emission boiling in scbcooled pool boiling and the role of Marangoni convection in its formation [J]. Experimental Thermal and Fluid Science, 2013, 50: 97-106
[19]	Kim J, Oh B D, Kim M H. Experimental study of pool temperature effects on nucleate pool boiling [J]. Int.J.Multiphase Flow, 2006, 32: 208-231
[20]	Suzuki K, Yuki K, Hong C. Subcooled boiling with microbubble emission (on mechanism of MEB generation)//22nd ISTP [C]. Delft, Netherlands, 2011
[21]	Florschuetz L W, Chao B T. On the mechanics of vapor bubble collapse [J]. J.Heat Transfer, 1965, 87: 209-220
[22]	Wittke D D, Chao B T. Collapse of vapor bubbles with translator motion [J]. J.Heat Transfer, 1967, 89: 17-24
[23]	Rayleigh L. On the pressure developed in a liquid during the collapse of a spherical cavity [J]. Philosophical Magazine, 1917, 34 (200): 94-98
[24]	Knapp R T, Hollander A. Laboratory investigations of the mechanism of cavitation [J]. Trans.ASME, 1948, 70: 419-435
[25]	Plesset M S, Zwick S A. The growth of vapor bubbles in superheated liquids [J]. Applied Physics, 1954, 25: 493-500

气泡微细化沸腾过程中气泡冷凝破裂现象

Condensation and collapse of bubbles in region of microbubble emission boiling

PDF (PC)

可视化

被引次数

摘要/Abstract

引用本文

使用本文

参考文献 25

相关文章 15

编辑推荐

Metrics

本文评价

[1]	周绍华, 詹飞龙, 丁国良, 张浩, 邵艳坡, 刘艳涛, 郜哲明. 短管节流阀内流动噪声的实验研究及降噪措施[J]. 化工学报, 2023, 74(S1): 113-121.
[2]	苏伟, 马东旭, 金旭, 刘忠彦, 张小松. 表面润湿性对霜层传递特性影响可视化实验研究[J]. 化工学报, 2023, 74(S1): 122-131.
[3]	张双星, 刘舫辰, 张义飞, 杜文静. R-134a脉动热管相变蓄放热实验研究[J]. 化工学报, 2023, 74(S1): 165-171.
[4]	张义飞, 刘舫辰, 张双星, 杜文静. 超临界二氧化碳用印刷电路板式换热器性能分析[J]. 化工学报, 2023, 74(S1): 183-190.
[5]	陈爱强, 代艳奇, 刘悦, 刘斌, 吴翰铭. 基板温度对HFE7100液滴蒸发过程的影响研究[J]. 化工学报, 2023, 74(S1): 191-197.
[6]	刘明栖, 吴延鹏. 导光管直径和长度对传热影响的模拟分析[J]. 化工学报, 2023, 74(S1): 206-212.
[7]	王志国, 薛孟, 董芋双, 张田震, 秦晓凯, 韩强. 基于裂隙粗糙性表征方法的地热岩体热流耦合数值模拟与分析[J]. 化工学报, 2023, 74(S1): 223-234.
[8]	江河, 袁俊飞, 王林, 邢谷雨. 均流腔结构对微细通道内相变流动特性影响的实验研究[J]. 化工学报, 2023, 74(S1): 235-244.
[9]	晁京伟, 许嘉兴, 李廷贤. 基于无管束蒸发换热强化策略的吸附热池的供热性能研究[J]. 化工学报, 2023, 74(S1): 302-310.
[10]	程成, 段钟弟, 孙浩然, 胡海涛, 薛鸿祥. 表面微结构对析晶沉积特性影响的格子Boltzmann模拟[J]. 化工学报, 2023, 74(S1): 74-86.
[11]	肖明堃, 杨光, 黄永华, 吴静怡. 浸没孔液氧气泡动力学数值研究[J]. 化工学报, 2023, 74(S1): 87-95.
[12]	李艺彤, 郭航, 陈浩, 叶芳. 催化剂非均匀分布的质子交换膜燃料电池操作条件研究[J]. 化工学报, 2023, 74(9): 3831-3840.
[13]	温凯杰, 郭力, 夏诏杰, 陈建华. 一种耦合CFD与深度学习的气固快速模拟方法[J]. 化工学报, 2023, 74(9): 3775-3785.
[14]	王玉兵, 李杰, 詹宏波, 朱光亚, 张大林. R134a在菱形离散肋微小通道内的流动沸腾换热实验研究[J]. 化工学报, 2023, 74(9): 3797-3806.
[15]	袁佳琦, 刘政, 黄锐, 张乐福, 贺登辉. 泡状入流条件下旋流泵能量转换特性研究[J]. 化工学报, 2023, 74(9): 3807-3820.