水平管降膜吸收局部传热传质特性的数值模拟

doi:10.11949/j.issn.0438-1157.20160890

化工学报 ›› 2017, Vol. 68 ›› Issue (4): 1364-1372.DOI: 10.11949/j.issn.0438-1157.20160890

水平管降膜吸收局部传热传质特性的数值模拟

李美军^1,2,3, 路源^1,2, 张士杰^1,2, 肖云汉^1,2

1 中国科学院工程热物理研究所先进能源动力重点实验室, 北京 100190;
2 中国科学院能源动力研究中心, 江苏连云港 222069;
3 中国科学院大学, 北京 100049

收稿日期:2016-06-29 修回日期:2016-12-28 出版日期:2017-04-05 发布日期:2017-04-05
通讯作者: 张士杰
基金资助:
“政府间国际科技创新合作”重点专项中美能源与水（2016YFE0102400）。

Numerical study of local heat and mass transfer characteristics of falling films over horizontal tubes

LI Meijun^1,2,3, LU Yuan^1,2, ZHANG Shijie^1,2, XIAO Yunhan^1,2

1 Key Laboratory of Advanced Energy and Power, Institute of Engineering Thermophysics, Chinese Academy of Sciences, Beijing 100190, China;
2 Research Center for Clean Energy and Power, Chinese Academy of Sciences, Lianyungang 222069, Jiangsu, China;
3 University of Chinese Academy of Sciences, Beijing 100049, China

Received:2016-06-29 Revised:2016-12-28 Online:2017-04-05 Published:2017-04-05
Supported by:
supported by the Foundation of US/China Clean Energy Research Center for Water-Energy Technologies (2016YFE0102400).

摘要/Abstract

摘要：

为分析滴状和柱状流型下纯水蒸气水平管外降膜吸收过程的局部传热传质特性，建立非稳态数值模型考虑吸收过程中降膜区和管间区内液相的实际流动特征及气液两相的传质，同时对多管排区域采用实际边界条件，且考虑气液两相的传热过程。溶液的液膜Reynolds数范围为11~38。结果表明，与文献实验对比，相同流量下溶液出口浓度和温度的平均相对误差在2%以内；滴状和柱状流型下，降膜区溶液的平均浓度和温度均迅速下降，管间区先上升后下降，降膜区溶液的局部吸收速率分别约为管间区的10倍和7倍；柱状流型下降膜区的吸收速率明显小于滴状流型，管间区相差很小；吸收达到稳定后，滴状流型下溶液的平均浓度和温度变化均大于柱状流型，四排管降膜区溶液的浓度变化量依次增大，温度变化量依次减小。

关键词: 两相流, 降膜, 传热传质, 吸收, 计算流体力学

Abstract:

In order to investigate the local heat and mass transfer characteristics in vapor absorption of falling film flow on a bundle of horizontal tubes in droplet and column flow mode, a transient computational fluid dynamics(CFD) model was developed. The model not only considered the simultaneous hydrodynamic characteristics and mass transfer of LiBr solution flowing on and between tubes, but also considered the real boundary condition for multi-rank tubes and the heat transfer between phases. Simulations were performed for the film Reynolds number varying from 11 to 38. The simulation results showed that the solution outlet concentration and temperature in different mass flow rates agreed well with the experimental data in reference, with deviations less than 2%. In both the droplet and column flow modes, the average concentration and temperature decreased rapidly in the falling-film regions, but increased then decreased in the inter-tube regions. The local absorption rates in the falling-film regions were about 10 times as much as that in the inter-tube regions in the droplet flow mode, and 7 times in the column flow mode. In the falling-film regions, the absorption rate in the column flow mode is obviously less than that in the droplet flow mode. However, in the inter-tube regions, the absorption rates in the two different flow modes were almost the same. When the absorption process reached a steady state, the variations of average concentration and temperature in the droplet flow mode were greater than that in the column flow mode. The average concentration variations of the falling-film regions on the four tubes increased in turn, but the average temperature variations decreased.

Key words: two-phase flow, falling film, heat and mass transfer, absorption, computational fluid dynamics

中图分类号:

TK124

李美军, 路源, 张士杰, 肖云汉. 水平管降膜吸收局部传热传质特性的数值模拟[J]. 化工学报, 2017, 68(4): 1364-1372.

LI Meijun, LU Yuan, ZHANG Shijie, XIAO Yunhan. Numerical study of local heat and mass transfer characteristics of falling films over horizontal tubes[J]. CIESC Journal, 2017, 68(4): 1364-1372.

参考文献 30

[1]	JEONG S, GARIMELLA S. Falling-film and droplet mode heat and mass transfer in a horizontal tube LiBr/water absorber[J]. International Journal of Heat and Mass Transfer, 2002, 45(7):1445-1458.
[2]	BABADI F, FARHANIEH B. Characteristics of heat and mass transfer in vapor absorption of falling film flow on a horizontal tube[J]. International Communications in Heat and Mass Transfer, 2005, 32(9):1253-1265.
[3]	SUAMANIAM V, GARIMELLA S. From measurements of hydrodynamics to computation of species transport in falling films[J]. International Journal of Refrigeration, 2009, 32(4):607-626.
[4]	ISLAM M R. Absorption process of a falling film on a tubular absorber:an experimental and numerical study[J]. Applied Thermal Engineering, 2008, 28(11/12):1386-1394.
[5]	HIDOURI N, CHERMITI I, AHIM A B. Second law analysis of a gas-liquid absorption film[J]. Journal of Thermodynamics, 2013, 2013(1):1-10.
[6]	崔晓钰, 蔡祖恢, 李美玲. 溴化锂降膜吸收过程热质传递问题的研究进展[J]. 华东工业大学学报, 1997, 19(2):35-40.CUI X Y, CAI Z H, LI M L. The advancement of research on heat and mass transfer in falling-film absorption using lithium bromide aqueous solutions[J]. Journal of East China University of Technology, 1997, 19(2):35-40.
[7]	PAPAEFTHIMIOU V D, KARAMPINOS D C, ROGDAKIS E D. A detailed analysis of water-vapor absorption in LiBr-H2O solution on a cooled horizontal tube[J]. Applied Thermal Engineering, 2006, 26(17/18):2095-2102.
[8]	KILLION J D, GARIMELLA S. A critical review of models of coupled heat and mass transfer in falling-film absorption[J]. International Journal of Refrigeration, 2001, 24(8):755-797.
[9]	WANG M X, LIU C F. Study on the falling film absorption outside smooth and enhanced tubes[J]. Journal of Hydrodynamics, 2006, 18(4):405-410.
[10]	AURACHER H, WOHLFEIL A, ZIEGLER F. A simple physical model for steam absorption into a falling film of aqueous lithium bromide solution on a horizontal tube[J]. Heat Mass Transfer, 2008, 44(12):1529-2536.
[11]	LI M J, LU Y, ZHANG S J, et al. A numerical study of effects of counter-current gas flow rate on local hydrodynamic characteristics of falling films over horizontal tubes[J]. Desalination, 2016, 383(1):68-80.
[12]	YIN H, QU M, ARCHER D H. Model based experimental performance analysis of a microscale LiBr-H2O steam-driven double-effect absorption chiller[J]. 2010, 30(13):1741-1750.
[13]	KIM D S, FERREIRA C A I. Analytic modelling of a falling film absorber and experimental determination of transfer coeffiecients[J]. International Journal of Heat and Mass Transfer, 2009, 52(21/22):4757-4765.
[14]	BANASIAK K, KOZIOL J. Mathematical modelling of a LiBr-H2O absorption chiller including two-dimensional distributions of temperature and concentration fields for heat and mass exchangers[J]. International Journal of Thermal Sciences, 2009, 48(9):1755-1762.
[15]	JAYASEKARA S, HALGAMUGE S K. Mathematical modelling and experimental verification of an absorption chiller including three dimensional temperature and concentration distributions[J]. Applied Energy, 2016, 106:232-242.
[16]	BO S S, MA X H, LAN Z, et al. Numerical simulation on the falling film absorption process in a counter-flow absorber[J]. Chemical Engineering Journal, 2010, 156(3):607-612.
[17]	KYUNG I, HEROLD K E, KANG Y T. Experimental verification of H2O/LiBr absorber bundle performance with smooth horizontal tubes[J]. International Journal of Refrigeration, 2007, 30(4):582-590.
[18]	RATTNER A S, GARIMELLA S. Simple mechanistically consistent formulation for volume-of-fluid based computations of condensing flows[J]. Journal of Heat Transfer, 2014, 136(7):1-9.
[19]	KILLION J D, GARIMELLA S. Gravity-driven flow of liquid films and droplets in horizontal tube banks[J]. International Journal of Refrigeration, 2003, 26 (5):516-526.
[20]	KILLION J D, GARIMELLA S. Pendant droplet motion for absorption on horizontal tube banks[J]. International Journal of Heat and Mass Transfer, 2004, 47 (19/20):4403-4414.
[21]	SUAMANIAM V. Computational analysis of binary-fluid heat and mass transfer in falling films and droplets[D]. Atlanta:Georgia Institute of Technology, 2008.
[22]	KYUNG I, HEROLD K E, KANG Y T. Model for absorption of water vapor into aqueous LiBr flowing over a horizontal smooth tube[J]. International Journal of Refrigeration, 2007. 30(4):591-600.
[23]	HARIKRISHNAN L, TIWARI S, MAIYA M P. Numerical study of heat and mass transfer characteristics on a falling film horizontal tubular absorber for R-134a-DMAC[J]. International Journal of Thermal Sciences, 2011, 50 (2):149-159.
[24]	HARIKRISHNAN L, TIWARI S, MAIYA M P. Effect of solution temperature and absorber pressure in R-134a-DMAC system using horizontal tubular absorbers[J]. International Journal of Low-Carbon Technologies Advance Access, 2011,21:1-9.
[25]	HARIKRISHNAN L, MAIYA M P, TIWARI S, et al. Heat and mass transfer characteristics of absorption of R134a into DMAC in a horizontal tube absorber[J]. Heat Mass Transfer, 2009, 45(12):1483-1491.
[26]	王长庆, 陆震. 溴化锂降膜式发生器水平圆管外柱状布液液膜流动的研究[J]. 制冷与空调, 1999, (1):39-42.WANG C Q, LU Z. Study on LiBr solution falling film flow in the column flow mode in generator with horizontal tubes[J]. Journal of Refrigeration and Air-Conditioning, 1999, (1):39-42.
[27]	姜传胜. 溴化锂溶液水平管吸收器降膜吸收传热传质规律研究[D]. 青岛:中国石油大学, 2006.JIANG C S. Analysis of heat and mass transfer of LiBr solution falling film absorption in absorber with horizontal tube[D]. Qingdao:China University of Petroleum, 2006.
[28]	KYUNG I, HEROLD K E. Performance of horizontal smooth tube absorber with and without 2-ethyl-hexanol[J]. Journal of Heat Transfer, 2002, 124(1):177-183.
[29]	YOUNG D L. Time-dependent Multi-material Flow with Large Fluid Distortion. Numerical Methods for Fluid Dynamics[M]. New York:Academic Press, 1982
[30]	HIRT C W, NICHOLS B D. Volume of fluid (VOF) method for the dynamics of free boundaries[J]. Journal of Computational Physics, 1981, 39(1):201-225.

水平管降膜吸收局部传热传质特性的数值模拟

Numerical study of local heat and mass transfer characteristics of falling films over horizontal tubes

PDF (PC)

可视化

被引次数

摘要/Abstract

引用本文

使用本文

参考文献 30

相关文章 15

编辑推荐

Metrics

本文评价

[1]	周绍华, 詹飞龙, 丁国良, 张浩, 邵艳坡, 刘艳涛, 郜哲明. 短管节流阀内流动噪声的实验研究及降噪措施[J]. 化工学报, 2023, 74(S1): 113-121.
[2]	江河, 袁俊飞, 王林, 邢谷雨. 均流腔结构对微细通道内相变流动特性影响的实验研究[J]. 化工学报, 2023, 74(S1): 235-244.
[3]	张思雨, 殷勇高, 贾鹏琦, 叶威. 双U型地埋管群跨季节蓄热特性研究[J]. 化工学报, 2023, 74(S1): 295-301.
[4]	晁京伟, 许嘉兴, 李廷贤. 基于无管束蒸发换热强化策略的吸附热池的供热性能研究[J]. 化工学报, 2023, 74(S1): 302-310.
[5]	黄琮琪, 吴一梅, 陈建业, 邵双全. 碱性电解水制氢装置热管理系统仿真研究[J]. 化工学报, 2023, 74(S1): 320-328.
[6]	金正浩, 封立杰, 李舒宏. 氨水溶液交叉型再吸收式热泵的能量及分析[J]. 化工学报, 2023, 74(S1): 53-63.
[7]	肖明堃, 杨光, 黄永华, 吴静怡. 浸没孔液氧气泡动力学数值研究[J]. 化工学报, 2023, 74(S1): 87-95.
[8]	米泽豪, 花儿. 基于DFT和COSMO-RS理论研究多元胺型离子液体吸收SO₂气体[J]. 化工学报, 2023, 74(9): 3681-3696.
[9]	温凯杰, 郭力, 夏诏杰, 陈建华. 一种耦合CFD与深度学习的气固快速模拟方法[J]. 化工学报, 2023, 74(9): 3775-3785.
[10]	王玉兵, 李杰, 詹宏波, 朱光亚, 张大林. R134a在菱形离散肋微小通道内的流动沸腾换热实验研究[J]. 化工学报, 2023, 74(9): 3797-3806.
[11]	袁佳琦, 刘政, 黄锐, 张乐福, 贺登辉. 泡状入流条件下旋流泵能量转换特性研究[J]. 化工学报, 2023, 74(9): 3807-3820.
[12]	何松, 刘乔迈, 谢广烁, 王斯民, 肖娟. 高浓度水煤浆管道气膜减阻两相流模拟及代理辅助优化[J]. 化工学报, 2023, 74(9): 3766-3774.
[13]	邢雷, 苗春雨, 蒋明虎, 赵立新, 李新亚. 井下微型气液旋流分离器优化设计与性能分析[J]. 化工学报, 2023, 74(8): 3394-3406.
[14]	张瑞航, 曹潘, 杨锋, 李昆, 肖朋, 邓春, 刘蓓, 孙长宇, 陈光进. ZIF-8纳米流体天然气乙烷回收工艺的产品纯度关键影响因素分析[J]. 化工学报, 2023, 74(8): 3386-3393.
[15]	胡兴枝, 张皓焱, 庄境坤, 范雨晴, 张开银, 向军. 嵌有超小CeO₂纳米粒子的碳纳米纤维的制备及其吸波性能[J]. 化工学报, 2023, 74(8): 3584-3596.