扁管换热器内纵向涡强度与换热强度对应关系

doi:10.11949/j.issn.0438-1157.20151231

化工学报 ›› 2016, Vol. 67 ›› Issue (5): 1858-1867.DOI: 10.11949/j.issn.0438-1157.20151231

扁管换热器内纵向涡强度与换热强度对应关系

宋克伟, 刘松, 王良璧

兰州交通大学机电学院, 铁道车辆热工教育部重点实验室, 甘肃兰州 730070

收稿日期:2015-07-31 修回日期:2015-10-26 出版日期:2016-05-05 发布日期:2016-05-05
通讯作者: 王良璧
基金资助:
国家自然科学基金项目(51366008,51376086);甘肃省杰出青年基金项目(145RJDA324)。

Relationship between longitudinal vortex intensity and heat transfer intensity of flat tube heat exchanger

SONG Kewei, LIU Song, WANG Liangbi

Key Laboratory of Railway Vehicle Thermal Engineering of MOE, Lanzhou Jiaotong University, Lanzhou 730070, Gansu, China

Received:2015-07-31 Revised:2015-10-26 Online:2016-05-05 Published:2016-05-05
Supported by:
supported by the National Natural Science Foundation of China (51366008, 51376086) and the Gansu Provincial Foundation for Distinguished Young Scholars (145RJDA324).

摘要/Abstract

摘要：

纵向涡强化传热技术在管翅式换热器中得到了广泛的应用。但是一直以来对纵向涡强化传热的研究主要停留在涡产生器结构参数及布置方式对换热的影响方面,文献对纵向涡强度与换热强度之间定量关系的研究鲜有报道。建立了采用纵向涡强化传热的扁管管翅换热器数值模型,采用二次流强度参数Se分析了翅片及涡产生器结构参数变化时,通道内纵向涡强度与换热强度之间的定量关系;并定量分析了通道中涡产生器引起的纵向涡强度增量与传热强化量之间的定量关系。结果表明:翅片及涡产生器结构参数变化时,Nu、Se与Re之间,以及阻力系数f与Re及Se之间均不存在定量对应关系,但Se与Nu以及ΔSe与ΔNu之间存在对应关系。这表明,在布置有纵向涡产生器的扁管管翅换热器翅侧通道内,纵向涡强度决定了通道内的换热强度。

关键词: 涡产生器, 纵向涡强度, 换热强度, 定量关系, 传热, 数值分析

Abstract:

The longitudinal vortices can potentially enhance heat transfer with small pressure loss penalty. Vortex generators (VGs) which can generate longitudinal vortices are widely used in fin-and-tube heat exchangers for heat transfer enhancement. But for a long time, researches are carried out focusing on the effect of the shape and parameters of VGs on heat transfer and the relationship between the longitudinal vortices intensity and heat transfer intensity is analyzed qualitatively. The quantitative relationship between the longitudinal vortices intensity and heat transfer intensity is seldom reported. Longitudinal vortex is a typical secondary flow, and thus the longitudinal vortex intensity can be defined using the secondary flow intensity parameter. In this paper, the numerical models of flat tube bank fin heat exchanger with VGs mounted on the fin surfaces are studied for different fin and VGs parameters. The longitudinal vortices intensity is quantitatively defined using the nondimensional secondary flow intensity parameter Se. The relationship between the longitudinal vortices intensity and the heat transfer intensity and that between the increment values of Se and Nu caused by the longitudinal vortices are quantitatively studied. The results show that there is no corresponding relationships neither between Nu and Re, nor between Se and Re. Similarly, no linear relationship exists between the friction factor f and the values of Re and Se. But the corresponding relationship exists not only between Se and Nu but also ΔSe and ΔNu. The longitudinal vortices intensity determines the heat transfer intensity in the flat tube fin heat exchanger.

Key words: vortex generator, longitudinal vortices intensity, heat transfer intensity, quantitative relationship, heat transfer, numerical analysis

中图分类号:

TK121

宋克伟, 刘松, 王良璧. 扁管换热器内纵向涡强度与换热强度对应关系[J]. 化工学报, 2016, 67(5): 1858-1867.

SONG Kewei, LIU Song, WANG Liangbi. Relationship between longitudinal vortex intensity and heat transfer intensity of flat tube heat exchanger[J]. CIESC Journal, 2016, 67(5): 1858-1867.

参考文献 22

[1]	FIEBIG M. Vortices and heat transfer [J]. Z. Angew. Math. Mech., 1997, 77: 3-18.
[2]	WU J M, TAO W Q. Impact of delta winglet vortex generators on the performance of a novel fin-tube surfaces with two rows of tubes in different diameters [J]. Energy Convers. Manage, 2011, 52(8/9): 2895-2901.
[3]	WANG Q W, CHEN Q Y, WANG L. Experimental study of heat transfer enhancement in narrow rectangular channel with longitudinal vortex generators [J]. Nucl. Eng. Des., 2007, 237: 686-693.
[4]	BISWAS G, DEB P, BISWAS S. Generation of longitudinal streamwise vortices — a device for improving heat exchanger design [J]. J. Heat Transfer, 1994, 116: 588-597.
[5]	FIEBIG M. Embedded vortices in internal flow: heat transfer and pressure loss enhancement [J]. Int. J. Heat Fluid Flow, 1998, 16: 376-388.
[6]	LEI Y G, HE Y L, TIAN L T, et al. Hydrodynamics and heat transfer characteristics of a novel heat exchanger with delta-winglet vortex generators [J]. Chem. Eng. Sci., 2010, 65: 1551-1562.
[7]	CHEN Y, FIEBIG M, MITRA N K. Heat transfer enhancement of finned oval tubes with staggered punched longitudinal vortex generators [J]. Int. J. Heat Mass Transfer, 2000, 43: 417-435.
[8]	SONG K W, WANG L B, FAN J F, et al. Numerical study of heat transfer enhancement of finned flat tube bank fin with vortex generators mounted on both surfaces of the fin [J]. Heat Mass Transfer, 2008, 44: 959-967.
[9]	TORRI K, KWAK K, NISHINO K. Heat transfer enhancement accompanying pressure-loss reduction with winglet-type vortex generators for fin tube heat exchangers [J]. Int. J Heat Mass Transfer, 2002, 45: 3795-3810.
[10]	TIAN L T, HE Y L, LEI Y G, et al. Numerical study of fluid flow and heat transfer in a flat-plate channel with longitudinal vortex generators by applying fluid synergy principles analysis [J]. Int. Commun. Heat Mass Transfer, 2009, 36: 111-120.
[11]	汉京晓, 周国兵. 平直和柱面小翼涡发生器诱发流动特性PIV实验研究[J]. 化工学报, 2013, 64(8): 2774-2780. DOI: 10.3969/j.issn. 0438-1157.2013.08.010. HAN J X, ZHOU G B. PIV investigation on induced flow characteristics in cylindrical winglet vortex generators [J]. CIESC Journal, 2013, 64(8): 2774-2780. DOI: 10.3969/j.issn. 0438-1157. 2013.08.010.
[12]	LEI Y G, HE Y L, TIAN L T, et al. Hydrodynamics and heat transfer characteristics of a novel heat exchanger with delta-winglet vortex generators [J]. Chem. Eng. Sci., 2010, 65: 1551-1562.
[13]	周国兵, 张于峰, 齐承英, 等.几种翼型涡流发生器强化换热及流阻性能的实验研究[J]. 天津大学学报, 2003, 36(6): 735-738. ZHOU G B, ZHANG Y F, QI C Y, et al.Experimental investigation of heat transfer enhancement and pressure drop of some wing-type vortex generators [J]. Transactions of Tianjin University, 2003, 36(6): 735-738
[14]	GENTRY M C, JACOBI A M. Heat transfer enhancement by delta-wing vortex generators on a flat plate: vortex interactions with the boundary layer [J]. Exp. Therm Fluid Sci., 1997, 14(3): 231-242.
[15]	KE F, WANG L B, HUA L, et al. The optimum angle of attack of delta winglet vortex generators on heat transfer performance of finned flat tube bank with considering nonuniform fin temperature [J]. Exp. Heat Transfer, 2006, 19: 227-249
[16]	YANG J S, HONG C H, CHOI G M. Heat transfer measurement using thermochromatic liquid crystal [J]. Curr. Appl. Phys., 2007, 7: 413-420.
[17]	吕静, 马济成, 杜雅萍. 纵向涡旋发生元LVG强化换热的实验研究[J]. 上海理工大学学报, 2001, 23(3): 283-285. DOI: 10.3969/j.issn. 1007-6735.2001.03.025. LÜ J, MA J C, DU Y P. Experimental study on heat transfer enhancement by using delta-winglet longitudinal vortex generators [J]. J. University of Shanghai for Science and Technology, 2001, 23(3): 283-285.DOI: 10.3969/j.issn.1007-6735.2001.03.025.
[18]	何雅玲, 楚攀, 谢涛. 纵向涡发生器在管翅式换热器中的应用及优化[J]. 化工学报, 2012, 63(3): 746-760. DOI: 10.3969/j.issn. 0438-1157. 2012.03.011. HE Y L, CHU P, XIE T. Application and optimization of fin-and-tube heat exchangers with longitudinal vortex generators [J]. CIESC Journal, 2012, 63(3): 746-760. DOI: 10.3969/j.issn.0438-1157. 2012.03.011.
[19]	宋克伟, 刘松, 王良璧. 换热器通道内反向旋转纵向涡间的干涉特性[J]. 化工学报, 2016, 67(4): 1233-1243. DOI: 10.11949/j.issn. 0438-1157.20150618. SONG K W, LIU S, WANG L B. Interaction characteristics between longitudinal vortices with counter-rotating directions in heat exchanger channel [J]. CIESC Journal, 2016, 67(4): 1233-1243. DOI: 10.11949/j.issn.0438-1157. 20150618.
[20]	SONG K W, WANG L B. The effectiveness of secondary flow produced by vortex generators mounted on both surfaces of the fin to enhance heat transfer in a flat tube bank fin heat exchanger [J]. J. Heat Transfer, 2013, 135: 041902.
[21]	CHEN Y Y, SONG K W, WANG L B, et al. Comparisons of local experimental results with numerical results of heat transfer enhancement of a flat tube bank fin with vortex generators [J]. Numer. Heat Transfer, Part A, 2009, 55: 144-162.
[22]	SONG K W, WANG L B. Effects of the interaction of longitudinal vortices on the flow field and heat transfer over a flat-tube-and-fin heat exchanger [J]. J. Enhanced Heat Transfer, 2014, 21(6): 439-462.

扁管换热器内纵向涡强度与换热强度对应关系

Relationship between longitudinal vortex intensity and heat transfer intensity of flat tube heat exchanger

PDF (PC)

可视化

被引次数

摘要/Abstract

引用本文

使用本文

参考文献 22

相关文章 15

编辑推荐

Metrics

本文评价

[1]	张双星, 刘舫辰, 张义飞, 杜文静. R-134a脉动热管相变蓄放热实验研究[J]. 化工学报, 2023, 74(S1): 165-171.
[2]	张义飞, 刘舫辰, 张双星, 杜文静. 超临界二氧化碳用印刷电路板式换热器性能分析[J]. 化工学报, 2023, 74(S1): 183-190.
[3]	陈爱强, 代艳奇, 刘悦, 刘斌, 吴翰铭. 基板温度对HFE7100液滴蒸发过程的影响研究[J]. 化工学报, 2023, 74(S1): 191-197.
[4]	刘明栖, 吴延鹏. 导光管直径和长度对传热影响的模拟分析[J]. 化工学报, 2023, 74(S1): 206-212.
[5]	王志国, 薛孟, 董芋双, 张田震, 秦晓凯, 韩强. 基于裂隙粗糙性表征方法的地热岩体热流耦合数值模拟与分析[J]. 化工学报, 2023, 74(S1): 223-234.
[6]	晁京伟, 许嘉兴, 李廷贤. 基于无管束蒸发换热强化策略的吸附热池的供热性能研究[J]. 化工学报, 2023, 74(S1): 302-310.
[7]	程成, 段钟弟, 孙浩然, 胡海涛, 薛鸿祥. 表面微结构对析晶沉积特性影响的格子Boltzmann模拟[J]. 化工学报, 2023, 74(S1): 74-86.
[8]	李艺彤, 郭航, 陈浩, 叶芳. 催化剂非均匀分布的质子交换膜燃料电池操作条件研究[J]. 化工学报, 2023, 74(9): 3831-3840.
[9]	王玉兵, 李杰, 詹宏波, 朱光亚, 张大林. R134a在菱形离散肋微小通道内的流动沸腾换热实验研究[J]. 化工学报, 2023, 74(9): 3797-3806.
[10]	齐聪, 丁子, 余杰, 汤茂清, 梁林. 基于选择吸收纳米薄膜的太阳能温差发电特性研究[J]. 化工学报, 2023, 74(9): 3921-3930.
[11]	李科, 文键, 忻碧平. 耦合蒸气冷却屏的真空多层绝热结构对液氢储罐自增压过程的影响机制研究[J]. 化工学报, 2023, 74(9): 3786-3796.
[12]	陈天华, 刘兆轩, 韩群, 张程宾, 李文明. 喷雾冷却换热强化研究进展及影响因素[J]. 化工学报, 2023, 74(8): 3149-3170.
[13]	洪瑞, 袁宝强, 杜文静. 垂直上升管内超临界二氧化碳传热恶化机理分析[J]. 化工学报, 2023, 74(8): 3309-3319.
[14]	杨越, 张丹, 郑巨淦, 涂茂萍, 杨庆忠. NaCl水溶液喷射闪蒸-掺混蒸发的实验研究[J]. 化工学报, 2023, 74(8): 3279-3291.
[15]	张贲, 王松柏, 魏子亚, 郝婷婷, 马学虎, 温荣福. 超亲水多孔金属结构驱动的毛细液膜冷凝及传热强化[J]. 化工学报, 2023, 74(7): 2824-2835.