介孔复合材料内界面热阻及热导率

doi:10.11949/j.issn.0438-1157.20160601

化工学报 ›› 2016, Vol. 67 ›› Issue (S1): 166-173.DOI: 10.11949/j.issn.0438-1157.20160601

介孔复合材料内界面热阻及热导率

李静¹, 冯妍卉², 张欣欣², 王戈³

1 重庆大学动力工程学院, 重庆 400044;
2 北京科技大学机械工程学院, 北京 100083;
3 北京科技大学材料科学与工程学院, 北京 100083

收稿日期:2016-05-09 修回日期:2016-05-19 出版日期:2016-08-31 发布日期:2016-08-31
通讯作者: 李静,lj202740@cqu.edu.cn
基金资助:
国家自然科学基金项目（51422601，51436001）。

Interfacial thermal resistance in mesoporous composites and its thermal conductivity

LI Jing¹, FENG Yanhui², ZHANG Xinxin², WANG Ge³

1 School of Power Engineering, Chongqing University, Chongqing 400044, China;
2 School of Mechanical Engineering, University of Science and Technology Beijing, Beijing 100083, China;
3 School of Materials Science and Engineering, University of Science and Technology Beijing, Beijing 100083, China

Received:2016-05-09 Revised:2016-05-19 Online:2016-08-31 Published:2016-08-31
Supported by:
supported by the National Natural Science Foundation of China (51422601, 51436001).

摘要/Abstract

摘要：

界面广泛存在于复合材料中，对介孔复合材料热物性起着决定性的影响，研究界面的导热特性对于认识和理解介孔复合材料的导热机制十分重要。利用非平衡的分子动力学模拟方法计算介孔复合材料中基材与填充物间的界面热阻，考察界面热阻随温度、材料质量差异的变化，进一步用界面热阻修正介孔复合材料的有效热导率。结果表明，界面热阻的数量级为10^-11m²·K·W^-1，并随温度升高逐渐降低。界面两端材料质量差异越大，界面热阻越高。可通过减小孔径、减小纳米线长度、增大纳米线间距、降低纳米线填充率来降低介孔复合材料的有效热导率。界面热阻能降低材料的有效热导率。孔径越小、纳米线间距越小、纳米线长度越长、填充率越高，界面热阻降低热导率效果越显著。

关键词: 复合材料, 介孔材料, 晶界热阻, 传热, 热导率, 界面

Abstract:

The interface widely exists in composite material, and it plays a decisive impact on the thermal properties of mesoporous composite material. Study on the thermal conductivity of the interface is very important to know and understand the heat transfer mechanism of mesoporous composite material. In this paper, the simulation method of non-equilibrium molecular dynamics was used to calculate the interfacial thermal resistance between base material and filler in the mesoporous composite material, and the interfacial thermal resistance was analyzed with different temperature and different quality of material. Furthermore, the interfacial thermal resistance was used to modify the effective thermal conductivity of the mesoporous composite material. The results showed that the magnitude of the interfacial thermal resistance was 10^-11m²·K·W^-1 and it would gradually decrease with the temperature increasing. Since temperature increasing leads to the phonons' number increasing at the interface, the number and the energy of phonons penetrating the interface will increase. The greater the difference of the interface material quality, the higher the interfacial thermal resistance. The effective thermal conductivity of the mesoporous composite material can be decreased by downsizing the pore diameter, reducing the length of nanowires, increasing the distance between the nanowires or reducing the filling rate of the nanowires.It can be seen that, with the increasing of the pore size, the effective thermal conductivity of the mesoporous composite of the Z direction decreases, and those of X direction and Y direction have no obvious change. The effective thermal conductivity considering the interfacial thermal resistance is smaller than that without consideration, so it will be known that the interfacial thermal resistance can reduce the thermal conductivity, especially under the small pore diameter. The percentage of the interfacial thermal resistance is between 1%-7%, which will drop off gradually with the increasing of pore size. The effect of reducing the thermal conductivity through the interfacial thermal resistance will be more significant by decreasing the pore diameter and the distance between the nanowires, or increasing the length of nanowires and the filling rate.

Key words: composites, mesoporous material, thermal resistance of grain boundary, heat transfer, thermal conductivity, interface

中图分类号:

TK124

李静, 冯妍卉, 张欣欣, 王戈. 介孔复合材料内界面热阻及热导率[J]. 化工学报, 2016, 67(S1): 166-173.

LI Jing, FENG Yanhui, ZHANG Xinxin, WANG Ge. Interfacial thermal resistance in mesoporous composites and its thermal conductivity[J]. CIESC Journal, 2016, 67(S1): 166-173.

参考文献 28

[1]	吴代鸣.固体物理基础[M].北京:高等教育出版社,2007. WU D M. Fundamentals of Solid State Physics[M]. Beijing:Higher Education Press, 2007.
[2]	王涛, 骆仲泱, 郭顺松, 等. 可控纳米流体的制备及热导率研究[J]. 浙江大学学报, 2007, 41(3):514-518. WANG T, LUO Z Y, GUO S S, et al. Preparation of controllable nanofluids and research on thermal conductivity[J]. J. Zhejiang Univ., 2007, 41(3):514-518.
[3]	NOLAS G S, LYON H B. Expanding the investigation of the thermoelectric properties of rare-earth-filled skutte-rudites[C]//16th International Conference on Thermo-electrics. 1997.
[4]	YANG J, MORELLI D T, MEISNER G P, et al. Effect of Sn substituting for Sb on the low-temperature transport properties of ytterbium-filled skutterudites[J]. Physical Review B, 2003, 67:165207.
[5]	NOLAS G S, YANG J, TAKIZAWA H. Transport properties of germanium-filled CoSb3[J]. Applied Physics Letters, 2004, 84(25):5210-5212.
[6]	BROIDO D A, REINECKE T L. Lattice thermal conductivity of superlattice structures[J]. Physical Review B, 2004, 70:081310.
[7]	GLAVIN B A. Low-temperature heat transfer in nanowires[J]. Physical Review Letters, 2001, 86(19):4318-4321.
[8]	LI D Y, WU Y Y, FAN R, et al. Thermal conductivity of Si/SiGe superlattice nanowires[J]. Applied Physics Letters, 2003, 83(15):3186-3188.
[9]	DAMES C, CHEN G. Theoretical phonon thermal con-ductivity of Si/Ge superlattice nanowires[J]. Journal of Applied Physics, 2004, 95(2):682-693.
[10]	CHEN G. Thermal conductivity and ballistic-phonon transport in the cross-plane direction of superlattices[J]. Physical Review B, 1998, 57:14960.
[11]	JU S, LIANG X. Investigation of argon nanocrystalline thermal conductivity by molecular dynamics simulation[J]. Journal of Applied Physics, 2010, 108:104307.
[12]	MAITI A, MAHAN G D, PANTELIDES S T. Dynamical simulations of nonequilibrium processes-heat flow and the Kapitza resistance across grain boundaries[J]. Solid State Communications, 1997, 102:517-521
[13]	CROCOMBETTE J, GELEBART L. Multiscale modeling of the thermal conductivity of polycrystalline silicon carbide[J]. Journal of Applied Physics, 2009, 106:083520.
[14]	SCHELLING P K, PHILLPOT S R, KEBLINSKI P. Kapitza conductance and phonon scattering at grain boundaries by simulation[J]. Journal of Applied Physics, 2004, 95(11):6082-6091.
[15]	HUANG X B, DONG W J, WANG G, et al. Synthesis of confined Ag nanowires within mesoporous silica via double solvent technique and their catalytic properties[J]. Journal of Colloid and Interface Science, 2011, 359(1):40-46.
[16]	BISCHOF C, HARTMANN M. Synthesis and characterization of ruthenium-containing MCM-41 and MCM-48 mesoporous materials[C]//12th Proceeding International Zeolite Conference. 1998, 2:809-816.
[17]	ADHYAPAK P V, KARANDIKAR P, VIJAYAMOHANAN K, et al. Syhthesis of silver nanowires inside mesoporous MCM-41 Host[J]. Mater Letter,2004,58:1168-1171.
[18]	CIUPARU D, CHEN Y, LIM S, et al. Uniform-diameter single-walled carbon nanotubes catalytically grown in cobalt-incorporated MCM-41[J]. Journal of Physical Chemistry B, 2004, 108(2):503-507.
[19]	JELLE R A S, JOHANNES D M, MARJAN V H, et al. Ordered mesoporous silica to study the preparation of Ni/SiO2 ex nitrate catalysts:impregnation, drying, and thermal treatments[J]. Chemistry of Materials, 2008, 20(9):2921-2931.
[20]	MULLER P F. A simple nonequilibrium molecular dynamics method for calculating the thermal conductivity[J]. Journal of Chemical Physics, 1997, 106:6082-6085.
[21]	SWARTZ E T, POHL R O. Thermal boundary resistance[J]. Reviews of Modern Physics,1989, 61(3):605-668.
[22]	BELLIS L D, PHELAN P E. Variations of acoustic and diffuse mismatch models in predicting thermal-boundary resistance[J]. Journal of Thermophysics and Heat Transfer, 2000, 14(2):144-150.
[23]	JU S, LIANG X, WANG S. Investigation of interfacial thermal resistance of bi-layer nanofilms by nonequilibrium molecular dynamics[J]. Journal of Physics D:Applied Physics, 2010, 43:085407.
[24]	HUANG C L, FENG Y H, ZHANG X X, et al. Prediction of thermal conductivity of aluminum nanocluster-filled mesoporous silica (Al/MCM-41)[J]. International Journal of Thermophysics, 2013, 34(12):2371-2384.
[25]	ZENG T F, CHEN G. Phonon heat conduction in thin films:impacts of thermal boundary resistance and internal heat generation[J]. Transaction of the ASME, Journal of Heat Transfer, 2001, 123:340-347.
[26]	ZENG S Q, HUNT A, GREIF R. Mean free path and apparent thermal conductivity of a gas in a porous medium[J]. Journal of Heat Transfer, 1995, 117(3):758-761.
[27]	LI J, FENG Y H, ZHANG X X, et al. Thermal conductivities of metallic nanowires with considering surface and grain boundary scattering[J]. Acta Physica Sinica, 2013, 62(18):186501.
[28]	YUAN S P, JIANG P X. Thermal conductivity of small nickel particles[J]. International Journal of Thermophysics, 2006, 27(2):581-595.

介孔复合材料内界面热阻及热导率

Interfacial thermal resistance in mesoporous composites and its thermal conductivity

PDF (PC)

可视化

摘要/Abstract

引用本文

使用本文

参考文献 28

相关文章 15

编辑推荐

Metrics

本文评价

[1]	周晓庆, 李春煜, 杨光, 蔡爱峰, 吴静怡. 液滴撞击不同曲率过冷波纹面结冰动力学行为及机理研究[J]. 化工学报, 2023, 74(S1): 141-153.
[2]	张双星, 刘舫辰, 张义飞, 杜文静. R-134a脉动热管相变蓄放热实验研究[J]. 化工学报, 2023, 74(S1): 165-171.
[3]	毕丽森, 刘斌, 胡恒祥, 曾涛, 李卓睿, 宋健飞, 吴翰铭. 粗糙界面上纳米液滴蒸发模式的分子动力学研究[J]. 化工学报, 2023, 74(S1): 172-178.
[4]	张义飞, 刘舫辰, 张双星, 杜文静. 超临界二氧化碳用印刷电路板式换热器性能分析[J]. 化工学报, 2023, 74(S1): 183-190.
[5]	陈爱强, 代艳奇, 刘悦, 刘斌, 吴翰铭. 基板温度对HFE7100液滴蒸发过程的影响研究[J]. 化工学报, 2023, 74(S1): 191-197.
[6]	刘明栖, 吴延鹏. 导光管直径和长度对传热影响的模拟分析[J]. 化工学报, 2023, 74(S1): 206-212.
[7]	王志国, 薛孟, 董芋双, 张田震, 秦晓凯, 韩强. 基于裂隙粗糙性表征方法的地热岩体热流耦合数值模拟与分析[J]. 化工学报, 2023, 74(S1): 223-234.
[8]	晁京伟, 许嘉兴, 李廷贤. 基于无管束蒸发换热强化策略的吸附热池的供热性能研究[J]. 化工学报, 2023, 74(S1): 302-310.
[9]	程成, 段钟弟, 孙浩然, 胡海涛, 薛鸿祥. 表面微结构对析晶沉积特性影响的格子Boltzmann模拟[J]. 化工学报, 2023, 74(S1): 74-86.
[10]	李艺彤, 郭航, 陈浩, 叶芳. 催化剂非均匀分布的质子交换膜燃料电池操作条件研究[J]. 化工学报, 2023, 74(9): 3831-3840.
[11]	王玉兵, 李杰, 詹宏波, 朱光亚, 张大林. R134a在菱形离散肋微小通道内的流动沸腾换热实验研究[J]. 化工学报, 2023, 74(9): 3797-3806.
[12]	陆俊凤, 孙怀宇, 王艳磊, 何宏艳. 离子液体界面极化及其调控氢键性质的分子机理[J]. 化工学报, 2023, 74(9): 3665-3680.
[13]	齐聪, 丁子, 余杰, 汤茂清, 梁林. 基于选择吸收纳米薄膜的太阳能温差发电特性研究[J]. 化工学报, 2023, 74(9): 3921-3930.
[14]	李科, 文键, 忻碧平. 耦合蒸气冷却屏的真空多层绝热结构对液氢储罐自增压过程的影响机制研究[J]. 化工学报, 2023, 74(9): 3786-3796.
[15]	陈天华, 刘兆轩, 韩群, 张程宾, 李文明. 喷雾冷却换热强化研究进展及影响因素[J]. 化工学报, 2023, 74(8): 3149-3170.