三维喷动床内异径干湿颗粒混合特性数值模拟

doi:10.11949/j.issn.0438-1157.20170700

化工学报 ›› 2017, Vol. 68 ›› Issue (12): 4545-4555.DOI: 10.11949/j.issn.0438-1157.20170700

三维喷动床内异径干湿颗粒混合特性数值模拟

李斌, 于洋, 马梦祥, 张磊, 陈翠玲

华北电力大学能源动力与机械工程学院, 河北保定 071003

收稿日期:2017-05-31 修回日期:2017-07-28 出版日期:2017-12-05 发布日期:2017-12-05
通讯作者: 于洋
基金资助:
国家自然科学基金项目（11602085）；河北省自然科学基金项目（E2016502098）。

Numerical simulation of mixing different sized wet and dry particles in three-dimensional spouted bed

LI Bin, YU Yang, MA Mengxiang, ZHANG Lei, CHEN Cuiling

School of Energy Power and Mechanical Engineering, North China Electric Power University, Baoding 071003, Hebei, China

Received:2017-05-31 Revised:2017-07-28 Online:2017-12-05 Published:2017-12-05
Supported by:
supported by the National Natural Science Foundation of China(11602085) and the Natural Science Foundation of Hebei Province(E2016502098).

摘要/Abstract

摘要：

基于计算流体力学-离散单元法，建立了三维喷动床内气固两相流数学模型，采用Fortran语言编制了并行数值模拟程序。对三维喷动床内两种不同直径的干颗粒及湿颗粒的混合特性进行了数值模拟，并从颗粒角度分析了双组分颗粒的运动机制。利用Lacey混合指数对床内整体以及特定区域的混合程度进行了定量分析，并研究了液桥体积、颗粒密度比以及表观气速对异径颗粒混合的影响。结果表明：在单孔射流喷动床内，干湿两种颗粒流动方式相似，湿颗粒无明显的聚团现象；液桥力对小直径的颗粒影响较大，使不同直径湿颗粒速度差减小；环隙区内颗粒的混合是影响整床颗粒混合的关键因素；液桥体积对颗粒混合的影响较大，对颗粒密度比以及表观气速的影响有限。

关键词: 湿颗粒, 两相流, 混合, 离散单元法, 数值模拟

Abstract:

Based on framework combined discrete element method and computational fluid dynamics, a gas-solid flow model in three-dimensional spouted bed was established and Fortran numerical simulation program was further developed. The mixing characteristics of two different diameter-sized wet or dry particles in three-dimensional spouted bed were simulated and the mixing mechanism of binary particles in the spouted bed was analyzed. Lacey mixing index was introduced to quantitatively analyze degree of mixing in whole bed and specific regions of the bed. The influences on mixing different sized particles were studied by volume of liquid bridge, ratio of particle densities and superficial gas velocity. The results show that both wet and dry particles flow similarly in single jet spouted bed without obvious agglomeration of wet particles. Liquid bridge had a greater influence on small particles than large ones, which reduced difference of velocity between wet particles with different diameters. Particle mixing in circular groove was critical to mixing across whole bed. Liquid bridge volume had a more significant influence on particle mixing, compared to ratio of particle densities and superficial gas velocity.

Key words: wet particle, two-phase flow, mixing, discrete element method, numerical simulation

中图分类号:

TQ051.1

李斌, 于洋, 马梦祥, 张磊, 陈翠玲. 三维喷动床内异径干湿颗粒混合特性数值模拟[J]. 化工学报, 2017, 68(12): 4545-4555.

LI Bin, YU Yang, MA Mengxiang, ZHANG Lei, CHEN Cuiling. Numerical simulation of mixing different sized wet and dry particles in three-dimensional spouted bed[J]. CIESC Journal, 2017, 68(12): 4545-4555.

参考文献 30

[1]	SALIKOV V, HEINRICH S, ANTONYUK S, et al. Investigations on the spouting stability in a prismatic spouted bed and apparatus optimization[J]. Advanced Powder Technology, 2015, 26(3):718-733.
[2]	LINK J M, DEEN N G, KUIPERS J A M, et al. PEPT and discrete particle simulation study of spout-fluid bed regimes[J]. AIChE Journal, 2010, 54(5):1189-1202.
[3]	张勇, 金保升, 钟文琪. 喷动气固流化床颗粒混合规律的实验研究[J]. 中国电机工程学报, 2008, 28(20):8-14. ZHANG Y, JIN B S, ZHONG W Q. Experimental investigation on particle mixing in spout-fluid bed[J]. Proceedings of the CSEE, 2008, 28(20):8-14.
[4]	VERMA V, DEEN N G, PADDING J T, et al. Two-fluid modeling of three-dimensional cylindrical gas-solid fluidized beds using the kinetic theory of granular flow[J]. Chemical Engineering Science, 2013, 102(15):227-245.
[5]	YANG S, LUO K, FANG M, et al. Parallel CFD-DEM modeling of the hydrodynamics in a lab-scale double slot-rectangular spouted bed with a partition plate[J]. Chemical Engineering Journal, 2014, 236(2):158-170.
[6]	YANG S, SUN Y, WANG J, et al. Influence of operating parameters and flow regime on solid dispersion behavior in a gas-solid spout-fluid bed[J]. Chemical Engineering Science, 2016, 142:112-125.
[7]	SALIKOV V, ANTONYUK S, HEINRICH S, et al. Characterization and CFD-DEM modelling of a prismatic spouted bed[J]. Powder Technology, 2014, 270:622-636.
[8]	彭丽, 吴迎亚, 李佳瑶, 等. 基于DEM模拟气固鼓泡床中颗粒碰撞参数对流场间歇性的影响[J]. 化工学报, 2015, 66(6):2041-2048. PENG L, WU Y Y, LI J Y, et al. Effect of granular collision parameters on DEM simulation of flow field intermittency in gas-solids bubbling fluidized bed[J]. CIESC Journal, 2015, 66(6):2041-2048.
[9]	张俊强, 纪律, 李斌, 等. 单孔射流流化床内颗粒混合特性的数值模拟[J]. 化工学报, 2017, 68(3):879-888. ZHANG J Q, JI L, LI B, et al. Numerical simulation of particle mixing in single jet fluidized bed[J]. CIESC Journal, 2017, 68(3):879-888
[10]	任立波, 韩吉田. 基于CFD-DEM耦合并行算法的锥形喷动床内离散颗粒数值模拟[J]. 东南大学学报(自然科学版), 2014, 44(5):993-998. REN L B, HAN J T. Numerical simulation of discrete particles in conical-base spouted bed based on parallel coupled CFD-DEM mode[J]. Journal of Southeast University (Natural Science Edition), 2014, 44(5):993-998.
[11]	GONIVA C, KLOSS C, DEEN N G, et al. Influence of rolling friction on single spout fluidized bed simulation[J]. Particuology, 2012, 10(5):582-591.
[12]	ZHANG Y, ZHONG W Q, JIN B S, et al. mixing and segregation behavior in a spout-fluid bed:effect of the particle density[J]. Industrial & Engineering Chemistry Research, 2013, 52(15):5489-5497.
[13]	ZHANG Y, ZHONG W Q, JIN B S, et al. Mixing and segregation behavior in a spout-fluid bed:effect of particle size[J]. Industrial & Engineering Chemistry Research, 2012, 51(43):14247-14257.
[14]	ZHANG Y, ZHONG W Q, RUI X, et al. Evaluation of mixing and mixing rate in a multiple spouted bed by image processing technique[J]. International Journal of Chemical Reactor Engineering, 2016, 15(1):103-115.
[15]	KARIMI H, MOLAEI D A. Prediction of equilibrium mixing state in binary particle spouted beds:effects of solids density and diameter differences, gas velocity, and bed aspect ratio[J]. Advanced Powder Technology, 2015, 26(5):1371-1382.
[16]	REN B, SHAO Y, ZHONG W Q, et al. Investigation of mixing behaviors in a spouted bed with different density particles using discrete element method[J]. Powder Technology, 2012, 222(5):85-94.
[17]	任冰, 钟文琪, 金保升, 等. 喷动床异径颗粒混合的离散元气固耦合模拟[J]. 工程热物理学报, 2013, 34(8):1475-1478. REN B, ZHONG W Q, JIN B S, et al. DEM simulation of mixing behaviors of binary particles with different sizes in spouted beds[J]. Journal of Engineering Thermophysics, 2013, 34(8):1475-1478.
[18]	XU H B, ZHONG W Q, YUAN Z L, et al. CFD-DEM study on cohesive particles in a spouted bed[J]. Powder Technology, 2017, 314:377-386.
[19]	徐惠斌, 钟文琪, Yu Aibing. 湿颗粒喷动床颗粒聚团特征的实验研究[J]. 工程热物理学报, 2017, 38(1):124-128. XU H B, ZHONG W Q, YU A B, et al. Experimental study on the agglomerate characteristics of particles in the wet spouted bed[J]. Journal of Engineering Thermophysics, 2017, 38(1):124-128.
[20]	NAGAHASHI Y, EPSTEIN N, GRACE J R, et al. Spouting enhancement by addition of small quantities of liquid to gas-spouted beds[J]. Canadian Journal of Chemical Engineering, 2010, 84(5):527-531.
[21]	SUTKAR V S, DEEN N G, PATIL A V, et al. Experimental study of hydrodynamics and thermal behavior of a pseudo-2D spout-fluidized bed with liquid injection[J]. AIChE Journal, 2015, 61(4):1146-1159.
[22]	SUTKAR V S, DEEN N G, PATIL A V, et al. CFD-DEM model for coupled heat and mass transfer in a spout fluidized bed with liquid injection[J]. Chemical Engineering Journal, 2016, 288:185-197.
[23]	BUIJTENEN M S, DEEN N G, HEINRICH S, et al. A discrete element study of wet particle-particle interaction during granulation in a spout fluidized bed[J]. Canadian Journal of Chemical Engineering, 2010, 87(2):308-317.
[24]	ZHU R R, ZHU W B, XING L C, et al. DEM simulation on particle mixing in dry and wet particles spouted bed[J]. Powder Technology, 2011, 210(1):73-81.
[25]	HE Y, PENG W, TANG T, et al. DEM numerical simulation of wet cohesive particles in a spout fluid bed[J]. Advanced Powder Technology, 2016, 27(1):93-104.
[26]	李斌, 纪律. 流化床炉内颗粒混合的离散单元法数值模拟[J]. 中国电机工程学报, 2012, 32(20):42-48. LI B, JI L. Numerical simulation of particle mixing in circulating fluidized bed with discrete element method[J]. Proceedings of the CSEE, 2012, 32(20):42-48.
[27]	孙其诚, 王光谦. 颗粒物质力学导论[M]. 北京:科学出版社, 2009. SUN Q C, WANG G Q. Introduction to the Granular Matter Mechanics[M]. Beijing:Science Press, 2009.
[28]	LI T, ZHANG Y, HERNÁNDEZ-JIMÉNEZ F. Investigation of particle-wall interaction in a pseudo-2D fluidized bed using CFD-DEM simulations[J]. Particuology, 2016, 25:10-22.
[29]	LACEY P M C. Developments in the theory of particle mixing[J]. Journal of Chemical Technology & Biotechnology, 1954, 4(5):257-268.
[30]	朱润孺, 朱卫兵, 邢力超, 等. 矩形喷动床混合特性的三维数值研究[J]. 中国电机工程学报, 2010, 30(17):12-16. ZHU R R, ZHU W B, XING L C, et al. A three-dimensional numerical investigation on particle mixing characteristics in rectangular spouted beds[J].Proceedings of the CSEE, 2010, 30(17):12-16.

三维喷动床内异径干湿颗粒混合特性数值模拟

Numerical simulation of mixing different sized wet and dry particles in three-dimensional spouted bed

PDF (PC)

可视化

被引次数

摘要/Abstract

引用本文

使用本文

参考文献 30

相关文章 15

编辑推荐

Metrics

本文评价

[1]	周绍华, 詹飞龙, 丁国良, 张浩, 邵艳坡, 刘艳涛, 郜哲明. 短管节流阀内流动噪声的实验研究及降噪措施[J]. 化工学报, 2023, 74(S1): 113-121.
[2]	叶展羽, 山訸, 徐震原. 用于太阳能蒸发的折纸式蒸发器性能仿真[J]. 化工学报, 2023, 74(S1): 132-140.
[3]	张义飞, 刘舫辰, 张双星, 杜文静. 超临界二氧化碳用印刷电路板式换热器性能分析[J]. 化工学报, 2023, 74(S1): 183-190.
[4]	陈爱强, 代艳奇, 刘悦, 刘斌, 吴翰铭. 基板温度对HFE7100液滴蒸发过程的影响研究[J]. 化工学报, 2023, 74(S1): 191-197.
[5]	谈莹莹, 刘晓庆, 王林, 黄鲤生, 李修真, 王占伟. R1150/R600a自复叠制冷循环开机动态特性实验研究[J]. 化工学报, 2023, 74(S1): 213-222.
[6]	王志国, 薛孟, 董芋双, 张田震, 秦晓凯, 韩强. 基于裂隙粗糙性表征方法的地热岩体热流耦合数值模拟与分析[J]. 化工学报, 2023, 74(S1): 223-234.
[7]	江河, 袁俊飞, 王林, 邢谷雨. 均流腔结构对微细通道内相变流动特性影响的实验研究[J]. 化工学报, 2023, 74(S1): 235-244.
[8]	宋嘉豪, 王文. 斯特林发动机与高温热管耦合运行特性研究[J]. 化工学报, 2023, 74(S1): 287-294.
[9]	张思雨, 殷勇高, 贾鹏琦, 叶威. 双U型地埋管群跨季节蓄热特性研究[J]. 化工学报, 2023, 74(S1): 295-301.
[10]	肖明堃, 杨光, 黄永华, 吴静怡. 浸没孔液氧气泡动力学数值研究[J]. 化工学报, 2023, 74(S1): 87-95.
[11]	温凯杰, 郭力, 夏诏杰, 陈建华. 一种耦合CFD与深度学习的气固快速模拟方法[J]. 化工学报, 2023, 74(9): 3775-3785.
[12]	王玉兵, 李杰, 詹宏波, 朱光亚, 张大林. R134a在菱形离散肋微小通道内的流动沸腾换热实验研究[J]. 化工学报, 2023, 74(9): 3797-3806.
[13]	袁佳琦, 刘政, 黄锐, 张乐福, 贺登辉. 泡状入流条件下旋流泵能量转换特性研究[J]. 化工学报, 2023, 74(9): 3807-3820.
[14]	何松, 刘乔迈, 谢广烁, 王斯民, 肖娟. 高浓度水煤浆管道气膜减阻两相流模拟及代理辅助优化[J]. 化工学报, 2023, 74(9): 3766-3774.
[15]	邢雷, 苗春雨, 蒋明虎, 赵立新, 李新亚. 井下微型气液旋流分离器优化设计与性能分析[J]. 化工学报, 2023, 74(8): 3394-3406.