响应面法优化一水硫酸氢钠流化催化精馏生产乙酸乙酯工艺条件

doi:10.3969/j.issn.0438-1157.2014.11.035

化工学报 ›› 2014, Vol. 65 ›› Issue (11): 4465-4471.DOI: 10.3969/j.issn.0438-1157.2014.11.035

响应面法优化一水硫酸氢钠流化催化精馏生产乙酸乙酯工艺条件

肖武, 李明月, 阮雪华, 贺高红, 都健

大连理工大学化工学院, 精细化工国家重点实验室, 膜科学与技术研究开发中心, 辽宁大连 116024

收稿日期:2014-08-02 修回日期:2014-08-13 出版日期:2014-11-05 发布日期:2014-11-05
通讯作者: 贺高红
基金资助:
国家自然科学基金项目(21206014,21125628);中央高校基本科研业务费专项资金项目(DUT14LAB14).

Optimization of ethyl acetate process conditions for sodium bisulfate fluidized catalytic distillation using response surface methodology

XIAO Wu, LI Mingyue, RUAN Xuehua, HE Gaohong, DU Jian

State Key Laboratory of Fine Chemical, R&D Center of Membrane Science and Technology, School of Chemical Engineering, Dalian University of Technology, Dalian 116024, Liaoning, China

Received:2014-08-02 Revised:2014-08-13 Online:2014-11-05 Published:2014-11-05
Supported by:
supported by the National Natural Science Foundation of China (21206014, 21125628) and the Fundamental Research Funds for the Central Universities (DUT14LAB14).

摘要/Abstract

摘要： 以新型的一水硫酸氢钠为催化剂,采用粉末状催化剂混合乙酸一起进料的加入方式,即流化催化精馏工艺,并利用响应面法优化乙酸乙酯催化精馏过程条件.首先,通过单因素灵敏度分析法对乙酸进料量、酸醇进料摩尔比、回流比、催化剂用量、釜底加热功率5个因素进行实验考察,确定了乙酸进料量、酸醇摩尔进料比、回流比3个关键因素的优化值及取值范围.根据单因素实验结果与精馏塔设备要求,塔釜加热功率和催化剂用量分别设定为68 W和2.0%(质量分数)乙酸,采用中心组合设计原则对乙酸进料量、酸醇进料摩尔比和回流比3个关键因素进行实验设计.以乙醇转化率为响应值,基于响应实验结果,利用响应面法对实验结果进行了方程回归,得到3个关键因素与响应值的二次关联模型.通过方差分析和平行实验,证明该模型准确可用.优化后的乙酸乙酯流态化催化精馏工艺条件为乙酸进料量3.2 mol·h^-1,酸醇进料摩尔比为3.1,回流比为3.3,在此优化条件下进行实验,乙醇转化率为88.67%,比基于单因素灵敏度分析法得到的优化工艺条件下乙醇转化率高1.0%.

关键词: 乙酸乙酯, 催化精馏, 响应面法, 优化

Abstract: A novel fluidized catalytic distillation process was developed to produce ethyl acetate based on sodium bisulfate catalyst, and response surface method was used to optimize process parameters. Firstly, single factor sensitivity analysis of five parameters, such as catalyst amount, reflux ratio, bottom heating power, acid alcohol molar feed ratio, feed rate, were carried out, and three key parameters (reflux ratio, acid alcohol molar feed ratio and feed rate) and their optimum ranges were determined. Depending on the results of single factor experiments and hydraulic limit of distillation equipment, reboiler duty of column 68 W and the amount of catalyst 2.0%(mass) acetic acid were fixed. Then central composite design methodology was used to design the experimental cases. The correlation model between three key parameters and the conversion rate of ethanol was obtained by response surface methodology based on the experimental results. By the analysis of variance and parallel experiments, the model was proved to be accurate and available. Finally, the optimum conditions were found to be feed flow of acetic acid 3.2 mol·h^-1 and mole ratio of acetic acid/ethanol 3.1, reflux ratio 3.3. Under the conditions, the conversion rate of ethanol is 88.67%. Compared to the optimization parameters by a single factor sensitivity analysis process, the conversion rate of ethanol is increased by 1.0%.

Key words: ethyl acetate, catalytic distillation, response surface methodology, optimization

中图分类号:

TQ225.24

肖武, 李明月, 阮雪华, 贺高红, 都健. 响应面法优化一水硫酸氢钠流化催化精馏生产乙酸乙酯工艺条件[J]. 化工学报, 2014, 65(11): 4465-4471.

XIAO Wu, LI Mingyue, RUAN Xuehua, HE Gaohong, DU Jian. Optimization of ethyl acetate process conditions for sodium bisulfate fluidized catalytic distillation using response surface methodology[J]. CIESC Journal, 2014, 65(11): 4465-4471.

参考文献 17

[1]	Xiang Hanyin (项汉银). Experiment and simulation of reactive distillation process for synthesizing ethyl acetate [J]. Computers and Applied Chemistry (计算机与应用化学), 2009, 26(6): 789-793
[2]	Liu Y J, Lotero E, Goodwin J G. A comparison of the esterification of acetic acid with methanol using heterogeneous versus homogeneous acid catalysis [J]. Journal of Catalysis, 2006, 242(2): 278-286
[3]	Chari M A, Syamasundar K. Silicagel supported sodium hydrogen-sulfate as a heterogeneous catalyst for high yield synthesis of 3,4-dihydropyrimidin-2(1H)-ones [J]. Journal of Molecular Catalysis A: Chemical, 2004, 221(1/2): 137-139
[4]	Chen Danyun (陈丹云), Guo Xinyong (郭新勇), Niu Jingyang (牛景扬). Applications and prospects of sodium bisulfate in catalytic reactions [J]. Hubei Chemical Industry (湖北化工), 2002, 5:20-22
[5]	Chi Weijun(迟卫军). The study on synthesis technology of ethyl acetate catalyzed by sodium bisulfate [J]. Chemistry and Adhesion(化学与粘合), 2007, 29(6): 451-453
[6]	Ge Wenfeng (葛文锋), Hu Xiaoping (胡晓萍), Wu Jia (吴嘉). Kinetics for esterification of acetic acid with ethanol catalyzed by sodium acid sulfate [J]. Chemical Reaction Engineering and Technology (化学反应工程与工艺), 2010, 26(3): 264-268
[7]	Quido Smejkal, Jirí Kolena, Jirí Hanika. Ethyl acetate synthesis by coupling of fixed-bed reactor and reactive distillation column—process integration aspects [J]. Chemical Engineering Journal, 2009, 154(1/2/3): 236-240
[8]	Tong Liwei, Chen Lifang, Ye Yinmei, Qi Zhiwen. Analysis of intensification mechanism of auxiliary reaction on reactive distillation: methyl acetate hydrolysis process as example [J]. Chemical Engineering Science, 2014, 106: 190-197
[9]	Noeres C, Dadhe K,Gesthuisen S E, et al. Model-based design, control and optimization of catalytic distillation processes [J]. Chemical Engineering and Processing, 2004, 43: 421-434
[10]	Hu Song, Zhang Bingjian, Hou Xiaoqiong, Li Deliang, Chen Qinglin. Design and simulation of an entrainer-enhanced ethyl acetate reactive distillation process [J]. Chemical Engineering and Processing: Process Intensification, 2011, 50(11/12): 1252-1265
[11]	Lv Bida, Liu Gongping, Dong Xueliang, Wei Wang, Jin Wanqin. Novel reactive distillation-pervaporation coupled process for ethyl acetate production with water removal from reboiler and acetic acid recycle [J]. Industrial & Engineering Chemistry Research, 2012, 51(23): 8079-8086
[12]	Raymond H Myers, Douglas C Montgomery, Christine M Anderson-cook. Response Surface Methodology—Process and Product Optimization Using Designed Experiments[M]. 3rd ed. Hoboken: Wiley, 2009
[13]	Piche S, Ribeiro N, Bacaoui A, Larachi F. Assessment of a redox alkaline/iron-chelate absorption process for the removal of dilute hydrogen sulfide in air emissions [J]. Chemical Engineering Science, 2005, 60(22): 6452-6461
[14]	Ahmad M A, Alrozi R. Optimization of preparation conditions for mangosteen peel-based activated carbons for the removal of remazol brilliant blue R using response surface methodology [J]. Chemical Engineering Journal, 2010, 165(3): 883-890
[15]	Sarrouh B, da Silva S. Application of response surface methodology for optimization of xylitol production from lignocellulosic hydrolysate in a fluidized bed reactor [J]. Chemical Engineering Technology, 2010, 33 (9):1481-1487
[16]	Wu Ruchun (吴如春), Yan Ruiyi (闫瑞一), Xie Tao (谢涛), Lan Ping (蓝平), Liao Anping (廖安平). Study on the continuous preparation process of ethyl acetate in one tower [J]. Chemistry World (化学世界), 2005(6): 354-357
[17]	Yadollah Tavan, Seyyed Hossein Hosseini. Design and simulation of a reactive distillation process to produce high-purity ethyl acetate [J]. Journal of the Taiwan Institute of Chemical Engineers, 2013, 44: 577-585

响应面法优化一水硫酸氢钠流化催化精馏生产乙酸乙酯工艺条件

Optimization of ethyl acetate process conditions for sodium bisulfate fluidized catalytic distillation using response surface methodology

PDF (PC)

可视化

被引次数

摘要/Abstract

引用本文

使用本文

参考文献 17

相关文章 15

编辑推荐

Metrics

本文评价

[1]	杨欣, 王文, 徐凯, 马凡华. 高压氢气加注过程中温度特征仿真分析[J]. 化工学报, 2023, 74(S1): 280-286.
[2]	何松, 刘乔迈, 谢广烁, 王斯民, 肖娟. 高浓度水煤浆管道气膜减阻两相流模拟及代理辅助优化[J]. 化工学报, 2023, 74(9): 3766-3774.
[3]	陈哲文, 魏俊杰, 张玉明. 超临界水煤气化耦合SOFC发电系统集成及其能量转化机制[J]. 化工学报, 2023, 74(9): 3888-3902.
[4]	齐聪, 丁子, 余杰, 汤茂清, 梁林. 基于选择吸收纳米薄膜的太阳能温差发电特性研究[J]. 化工学报, 2023, 74(9): 3921-3930.
[5]	陈国泽, 卫东, 郭倩, 向志平. 负载跟踪状态下的铝空气电池堆最优功率点优化方法[J]. 化工学报, 2023, 74(8): 3533-3542.
[6]	刘文竹, 云和明, 王宝雪, 胡明哲, 仲崇龙. 基于场协同和耗散的微通道拓扑优化研究[J]. 化工学报, 2023, 74(8): 3329-3341.
[7]	张曼铮, 肖猛, 闫沛伟, 苗政, 徐进良, 纪献兵. 危废焚烧处理耦合有机朗肯循环系统工质筛选与热力学优化[J]. 化工学报, 2023, 74(8): 3502-3512.
[8]	诸程瑛, 王振雷. 基于改进深度强化学习的乙烯裂解炉操作优化[J]. 化工学报, 2023, 74(8): 3429-3437.
[9]	邢雷, 苗春雨, 蒋明虎, 赵立新, 李新亚. 井下微型气液旋流分离器优化设计与性能分析[J]. 化工学报, 2023, 74(8): 3394-3406.
[10]	吴文涛, 褚良永, 张玲洁, 谭伟民, 沈丽明, 暴宁钟. 腰果酚生物基自愈合微胶囊的高效制备工艺研究[J]. 化工学报, 2023, 74(7): 3103-3115.
[11]	汤晓玲, 王嘉瑞, 朱玄烨, 郑仁朝. 基于Pickering乳液的卤醇脱卤酶催化合成手性环氧氯丙烷[J]. 化工学报, 2023, 74(7): 2926-2934.
[12]	文兆伦, 李沛睿, 张忠林, 杜晓, 侯起旺, 刘叶刚, 郝晓刚, 官国清. 基于自热再生的隔壁塔深冷空分工艺设计及优化[J]. 化工学报, 2023, 74(7): 2988-2998.
[13]	毕恩哲, 李双喜, 沙廉翔, 刘登宇, 陈凯放. 高温动压涨圈密封结构参数多目标优化分析[J]. 化工学报, 2023, 74(6): 2565-2579.
[14]	江锦波, 彭新, 许文烜, 门日秀, 刘畅, 彭旭东. 泵出型螺旋槽油气密封泄漏特性及参数影响研究[J]. 化工学报, 2023, 74(6): 2538-2554.
[15]	孙永尧, 高秋英, 曾文广, 王佳铭, 陈艺飞, 周永哲, 贺高红, 阮雪华. 面向含氮油田伴生气提质利用的膜耦合分离工艺设计优化[J]. 化工学报, 2023, 74(5): 2034-2045.