[BMIM]Cl/AlCl3离子液体低温电沉积铝过程

doi:10.3969/j.issn.0438-1157.2013.z1.022

化工学报 ›› 2013, Vol. 64 ›› Issue (S1): 147-154.DOI: 10.3969/j.issn.0438-1157.2013.z1.022

[BMIM]Cl/AlCl₃离子液体低温电沉积铝过程

康艳红, 陈仕谋, 张军玲, 郎海燕, 张锁江

中国科学院过程工程研究所, 离子液体清洁过程北京市重点实验室, 多相复杂系统国家重点实验室, 绿色过程与工程院重点实验室, 北京 100190

收稿日期:2013-10-31 修回日期:2013-11-07 出版日期:2013-12-30 发布日期:2013-12-30
通讯作者: 张锁江
作者简介:康艳红(1968—)，女，博士，副教授。
基金资助:
国家自然科学基金项目(21276257,21210006); 北京市自然科学基金项目(2132054); 国家科技支撑计划项目(2012BAF03B01)。

Electrodeposition of aluminum from [BMIM]Cl/AlCl₃ ionic liquids at low temperature

KANG Yanhong, CHEN Shimou, ZHANG Junling, LANG Haiyan, ZHANG Suojiang

Beijing Key Laboratory of Ionic Liquids Clean Process, State Key Laboratory of Multiphase Complex Systems, Institute of Process Engineering, Chinese Academy of Sciences, Beijing 100190, China

Received:2013-10-31 Revised:2013-11-07 Online:2013-12-30 Published:2013-12-30
Supported by:
supported by the National Natural Science Foundation of China (21276257,21210006)， the Natural Science Foundation of Beijing (2132054) and the National Key Technology Research and Development Program of the Ministry of Science and Technology of China (2012BAF03B01)).

摘要/Abstract

摘要： 采用玻碳/铂为惰性阳极，以1-丁基-3-甲基咪唑氯盐([BMIM]Cl/AlCl₃)离子液体体系为电解液，研究了离子液体电解铝工艺，优化了电解工艺条件，探讨了电解影响因素。结果表明，当电解液[BMIM]Cl∶AlCl₃摩尔比为1∶2.00时，随着温度的升高，铝的沉积槽电压逐渐减小，电流密度增加，但电解液的稳定性减弱，当温度达到90℃时，电解液分解明显。当电解温度一定时，随着[BMIM]Cl∶AlCl₃摩尔比的增加[(1∶1.25)~(1∶2.00)]，电流密度增加。通过赫尔槽实验，SEM、XRD分析了电解铝的沉积形貌和晶相结构。随电流密度的逐渐减小，沉积层变薄，晶相结构变化不大；相同电流密度区随温度的升高，沉积层逐渐变得粗糙。计算了不同槽间距下的槽压与电流密度的关系。

关键词: 离子液体, 电化学, 电解, 铝

Abstract: Aluminium can be electrodeposited from the ionic liquid 1-butyl-3-methyl imidazole salt chloride ([BMIM]/AlCl₃) below 100℃. It was found that voltage for aluminium deposition decreases with the increase of temperature and the current density increase with the increase of temperature. When the temperature reaches 90℃, the electrolyte become unstable. At a certain temperature, the current density increased gradually with the electrolyte [BMIM]Cl∶AlCl₃ molar ratio changes from 1∶1.25 to 1∶2.00. Effects of current density, temperature on the morphology of Al depositions were studied by Hull cell test. The surface on the cathode is characterized by using scanning electron microscope (SEM) and X-ray diffraction (XRD). Along with the current density decreasing, the electrochemical deposition layers of aluminium become thinner and thinner, but the crystal structure of the aluminium almost no change. Furthermore, the microstructures of deposition aluminium are greatly influenced by temperature. Based on all these investigations, the optimized technological parameters for electrodeposition of aluminum from [BMIM]Cl/AlCl₃ were obtained.

Key words: ionic liquid, electrochemistry, electrolysis, alumnium

中图分类号:

TQ151.9

康艳红, 陈仕谋, 张军玲, 郎海燕, 张锁江. [BMIM]Cl/AlCl₃离子液体低温电沉积铝过程[J]. 化工学报, 2013, 64(S1): 147-154.

KANG Yanhong, CHEN Shimou, ZHANG Junling, LANG Haiyan, ZHANG Suojiang. Electrodeposition of aluminum from [BMIM]Cl/AlCl₃ ionic liquids at low temperature[J]. CIESC Journal, 2013, 64(S1): 147-154.

参考文献 23

[1]	Pradhan D, Mantha D, Reddy R G. The effect of electrode surface modification and cathode overpotential on deposit characteristics in aluminum electrorefining using EMIC-AlCl3 ionic liquid electrolyte[J]. Electrochimica Acta， 2009, 54(26): 6661-6667
[2]	Kamavaram V, Mantha D, Reddy R G. Recycling of aluminum metal matrix composite using ionic liquids: Effect of process variables on current efficiency and deposit characteristics[J]. Electrochimica Acta, 2005, 50(16/17): 3286-3295
[3]	Yue G, Lu X, Zhu Y, Zhang X, Zhang S. Surface morphology, crystal structure and orientation of aluminium coatings electrodeposited on mild steel in ionic liquid[J]. Chemical Engineering Journal， 2009,147: 79-86
[4]	Giridhara P, Zein El Abedin S, Endresa F. Electrodeposition of aluminium from 1-butyl-1-methylpyrrolidinium chloride/AlCl3 and mixtures with 1-ethyl-3-methylimidazolium chloride/AlCl3[J]. Electrochimica Acta, 2012, 70: 210-214
[5]	Tang Jinwei, Azumi K. Optimization of pulsed electrodeposition of aluminum from AlCl3-1-ethyl-3-methylimidazolium chloride ionic liquid[J]. Electrochimica Acta， 2011, 56: 1130-1137
[6]	Li Bing, Fan Chunhua, Chen Yan, Lou Jingwei, Yan Lingguang. Pulse current electrodeposition of Al from an AlCl3-EMIC ionic liquid[J]. Electrochimica Acta， 2011, 56: 5478-5482
[7]	Zhang M M, Kamavaram V, Reddy R G. Aluminum electrowinning in ionic liquids at low temperature[J]. Light Metals, 2005: 583-588
[8]	Zheng Y, Zhang S, Lü X, Wang Q, Zuo Y, Liu L. Low-temperature electrodeposition of aluminium from lewis acidic 1-allyl-3-methylimidazolium chloroaluminate ionic liquids[J]. Chinese Journal of Chemical Engineering, 2012, 20(1): 130-39
[9]	Jiang T, Chollier Brym M J, Dube G, Lasia A, Brisard G M. Electrodeposition of aluminium from ionic liquids(Ⅱ): Studies on the electrodeposition of aluminum from aluminum chloride (AlCl3)-trimethylphenylammonium chloride (TMPAC) ionic liquids[J]. Surface & Coatings Technology, 2006, 201: 10-18
[10]	Pradhan D, Reddy R G. Electrochemical production of Ti-Al alloys using TiCl4-AlCl3-1-butyl-3-methyl imidazolium chloride (BmimCl) electrolytes[J]. Electrochimica Acta, 2009, 54(6):1874-1880
[11]	Ali M R, Nishikata A, Tsuru T. Electrodeposition of aluminum-chromium alloys from AlCl3-BPC melt and its corrosion and high temperature oxidation behaviors[J]. Electrochimica Acta, 1997, 42(15): 2347-2354
[12]	Ali M R, Nishikata A, Tsuru T. Electrodeposition of Co-Al alloys of different composition from the AlCl3-BPC-CoCl2 room temperature molten salt[J]. Electrochimica Acta, 1997, 42(12): 1819-1828
[13]	Tsuda T, Hussey C L， Stafford G R, Bonevich J E. Electrochemistry of titanium and the electrodeposition of Al-Ti alloys in the Lewis acidic aluminum chloride-1-ethyl-3-methylimidazolium chloride melt[J]. Journal of the Electrochemical Society， 2003, 150(4): C234-C243
[14]	Tsuda T, Hussey C L. Electrodeposition of aluminum-vanadium alloys from the aluminum chloride-1-ethyl-3-methylimidazolium chloride molten salt[J]. Electrochemical Society Series， 2003, 2002(27): 637-648
[15]	Endres F, Bukowski M, Hempelmann R, Natter H. Electrodeposition of nanocrystalline metals and alloys from ionic liquids[J]. Angewandte Chemie-International Edition, 2003, 42(29): 3428-3430
[16]	Zein El Abedin S. Electrochemical behavior of aluminum and some of its alloys in chloroaluminate ionic liquids: electrolytic extraction and electrorefining[J]. J. Solid State Electrochemistry, 2012, 16: 775-783
[17]	Abhishek Lahiri, Rupak Das. Spectroscopic studies of the ionic liquid during the electrodeposition of Al-Ti alloy in 1-ethyl-3-methylimidazolium chloride melt[J]. Materials Chemistry and Physics, 2012, 32: 34-38
[18]	Chen J, Xu B, Ling G. Amorphous Al-Mn coating on NdFeB magnets: electrodeposition from AlCl3-EMIC-MnCl2 ionic liquid and its corrosion behavior[J]. Materials Chemistry and Physics, 2012, 134: 1067-1071
[19]	Pan S J, Tsai W T, Chang J K, Sun, I W. Co-deposition of Al-Zn on AZ91D magnesium alloy in AlCl3-1-ethyl-3-methylimidazolium chloride ionic liquid[J]. Electrochimica Acta, 2010, 55(6): 2158-2162
[20]	Tsuda T, Arimoto S, Kuwabata S, Hussey C L. Electrodeposition of Al-Mo-Ti ternary alloys in the Lewis acidic aluminum chloride-1-ethyl-3-methylimidazolium chloride room-temperature ionic liquid[J]. Journal of the Electrochemical Society, 2008, 155(4): d256-d262
[21]	Pradhan D, Reddy R G. Dendrite-free aluminum electrodeposition from AlCl3-1-ethyl-3-methyl-imidazolium chloride ionic liquid electrolytes[J]. Metallurgical and Materials Transactions. 2012, 43B: 519-530
[22]	Abdul-Sada A K, Greenway A M, Seddon K R, Welton T. A fast-atom-bombardment mass-spectrometric study of room-temperature 1-ethyl-3-methylimidazolium chloroaluminate(Ⅲ) ionic liquids-evidence for the existence of the decachlorotrialuminate(Ⅲ) anion[J]. Organic Mass Spectrometry, 1993, 28(7): 759-765
[23]	Zheng Y, Dong K, Wang Q, Zhang J, Lu X. Density, viscosity, and conductivity of Lewis acidic 1-hydrogen-3-methylimidazolium chloroaluminate ionic liquids[J]. Journal of Chemical and Engineering Data, 2013, 58: 32-42

[BMIM]Cl/AlCl₃离子液体低温电沉积铝过程

Electrodeposition of aluminum from [BMIM]Cl/AlCl₃ ionic liquids at low temperature

PDF (PC)

可视化

摘要/Abstract

引用本文

使用本文

参考文献 23

相关文章 15

编辑推荐

Metrics

本文评价

[1]	黄琮琪, 吴一梅, 陈建业, 邵双全. 碱性电解水制氢装置热管理系统仿真研究[J]. 化工学报, 2023, 74(S1): 320-328.
[2]	胡超, 董玉明, 张伟, 张红玲, 周鹏, 徐红彬. 浓硫酸活化五氧化二钒制备高浓度全钒液流电池正极电解液[J]. 化工学报, 2023, 74(S1): 338-345.
[3]	王琪, 张斌, 张晓昕, 武虎建, 战海涛, 王涛. 氯铝酸-三乙胺离子液体/P₂O₅催化合成伊索克酸和2-乙基蒽醌[J]. 化工学报, 2023, 74(S1): 245-249.
[4]	车睿敏, 郑文秋, 王小宇, 李鑫, 许凤. 基于离子液体的纤维素均相加工研究进展[J]. 化工学报, 2023, 74(9): 3615-3627.
[5]	陈美思, 陈威达, 李鑫垚, 李尚予, 吴有庭, 张锋, 张志炳. 硅基离子液体微颗粒强化气体捕集与转化的研究进展[J]. 化工学报, 2023, 74(9): 3628-3639.
[6]	程业品, 胡达清, 徐奕莎, 刘华彦, 卢晗锋, 崔国凯. 离子液体基低共熔溶剂在转化CO₂中的应用[J]. 化工学报, 2023, 74(9): 3640-3653.
[7]	王俐智, 杭钱程, 郑叶玲, 丁延, 陈家继, 叶青, 李进龙. 离子液体萃取剂萃取精馏分离丙酸甲酯+甲醇共沸物[J]. 化工学报, 2023, 74(9): 3731-3741.
[8]	陈杰, 林永胜, 肖恺, 杨臣, 邱挺. 胆碱基碱性离子液体催化合成仲丁醇性能研究[J]. 化工学报, 2023, 74(9): 3716-3730.
[9]	陆俊凤, 孙怀宇, 王艳磊, 何宏艳. 离子液体界面极化及其调控氢键性质的分子机理[J]. 化工学报, 2023, 74(9): 3665-3680.
[10]	郑佳丽, 李志会, 赵新强, 王延吉. 离子液体催化合成2-氰基呋喃反应动力学研究[J]. 化工学报, 2023, 74(9): 3708-3715.
[11]	米泽豪, 花儿. 基于DFT和COSMO-RS理论研究多元胺型离子液体吸收SO₂气体[J]. 化工学报, 2023, 74(9): 3681-3696.
[12]	康飞, 吕伟光, 巨锋, 孙峙. 废锂离子电池放电路径与评价研究[J]. 化工学报, 2023, 74(9): 3903-3911.
[13]	宋明昊, 赵霏, 刘淑晴, 李国选, 杨声, 雷志刚. 离子液体脱除模拟油中挥发酚的多尺度模拟与研究[J]. 化工学报, 2023, 74(9): 3654-3664.
[14]	杨绍旗, 赵淑蘅, 陈伦刚, 王晨光, 胡建军, 周清, 马隆龙. Raney镍-质子型离子液体体系催化木质素平台分子加氢脱氧制备烷烃[J]. 化工学报, 2023, 74(9): 3697-3707.
[15]	胡亚丽, 胡军勇, 马素霞, 孙禹坤, 谭学诣, 黄佳欣, 杨奉源. 逆电渗析热机新型工质开发及电化学特性研究[J]. 化工学报, 2023, 74(8): 3513-3521.