气固两相流强化传热研究进展

doi:10.3969/j.issn.0438-1157.2014.07.010

摘要/Abstract

摘要： 在气流中加入颗粒，形成气固两相流。根据气流速度的不同，气固两相流分为鼓泡流态化、快速流态化、气力输送等形式。不同的流动形态，两相流内颗粒浓度及颗粒的运动规律不同，其传热特点也存在差异。通过回顾几种多相流流态的传热特点，总结了多相流与传热面换热的影响因素、气固两相流的传热机理与模型。气固两相流中颗粒浓度、颗粒运动对其传热起决定性作用，而操作参数（气流速度、床层压力、床层温度等）则主要通过改变颗粒浓度和颗粒运动影响传热。此外，通过气固两相流强化传热的应用实例——气固两相流与填充床的热交换，分析了颗粒在对流换热中所起的作用，并进一步提出了今后研究方向和难点所在。

关键词: 传热, 两相流, 流态化, 对流, 气固混合物

Abstract: By adding particles into a gas flow, a gas-solid flow is formed. As the gas velocity increases, the gas-solid flow shows different patterns as bubbling fluidization, circulating fluidization and pneumatic conveying, in which the concentration of particles and the motion of gas-solid mixture are different, influencing the heat transfer between the gas-solid flow and immersed surface. In this paper, the heat transfer characters of the three flow patterns are reviewed, and the influencing factors, heat transfer mechanism and models are summarized. The concentration of particles and their movement play a decisive role on the heat transfer, and the operating parameters (gas velocity, bed pressure, bed temperature, etc) influence the heat transfer through changing the particle concentration and movement. A case of heat transfer enhancement, the heat exchange between gas-solid mixture and fixed bed, is analyzed. In addition, the future research area and the difficulty are presented.

Key words: heat transfer, two-phase flow, fluidization, conduction, gas-solid mixture

中图分类号:

TQ022.4

刘传平, 李传, 李永亮, 丁玉龙, 王立. 气固两相流强化传热研究进展[J]. 化工学报, 2014, 65(7): 2485-2494.

LIU Chuanping, LI Chuan, LI Yongliang, DING Yulong, WANG Li. Heat transfer enhancement in gas-solid flow[J]. CIESC Journal, 2014, 65(7): 2485-2494.

参考文献 51

[1]	Jin Yong (金涌), Zhu Jingxu (祝京旭), Wang Zhanwen (汪展文), Yu Zhiqing (俞芷青). Fluidization Engineering Principles(流态化工程原理)[M]. Beijing: Tsinghua University Press, 2001: 17-24
[2]	Kuang Pingjian (邝平健), Cao Weiwu (曹伟武), Ruan Genjian (阮根健), Liu Wentie (刘文铁), Huang Jinbo (黄锦波). Theoretical analysis and experimental research on conductive heat transfer of dilute dust stream across tube [J]. Power Engineering (动力工程), 1998, 18 (1): 38-42
[3]	Kuang Pingjian (邝平健), Liu Wentie (刘文铁), Cao Weiwu (曹伟武). Theoretical analysis and experimental research on conductive heat transfer of circulating fluidized bed boilers in the upper dilute zone [J]. Energy Conservation Technology (节能技术), 2006, 24 (5): 429-433
[4]	Gao Xiang (高翔), Luo Zhongyang (骆仲泱), Zhou Jinsong (周劲松), Chen Yafei (陈亚非), Li Yaxin (李亚欣), Ni Mingjiang (倪明江), Cen Kefa (岑可法). Research on flow and heat transfer characteristic of tube array heat exchanger in particle laden cross flow of boiler [J]. Journal of Engineering Thermophysics (工程热物理学报), 2000, 21 (1): 76-80
[5]	Zhou J, Luo Z, Gao X, Ni M, Cen K. Effect of particle loading on heat transfer enhancement in a gas-solid suspension cross flow [J]. Journal of Zhejiang University Science, 2002, 3 (4): 381-386
[6]	Basu P, Nag P K. An investigation into heat transfer in circulating fluidized beds [J]. International Journal of Heat and Mass Transfer, 1987, 30 (11): 2399-2409
[7]	Cheng Leming (程乐鸣), Luo Zhongyang (骆仲泱), Li Xuantian (李绚天), Ni Mingjiang (倪明江), Cen Kefa (岑可法). Membrane wall heat transfer in a circulating fluidized bed and its modeling[J]. Journal of Engineering Thermophysics (工程热物理学报), 1998, 19 (4): 514-518
[8]	Wang Qinhui (王勤辉), Luo Zhongyang (骆仲泱), Fang Mengxiang (方梦祥), Li Xuantian (李绚天), Cheng Leming (程乐鸣), Ni Mingjiang (倪明江), Cen Kefa (岑可法). An overall mathematical model of CFB boiler and comparison of model predications with test results[J]. Journal of Engineering Thermophysics(工程热物理学报), 1998, 19(2):251-255
[9]	Sun Xianbin (孙献斌), He Wangquan (何王全), Lü Huai'an (吕怀安), Zhang Min (张敏), Xu Zhengquan (徐正泉), Gao Hongpei (高洪培), Xiao Ping (肖平), Pan Dong (潘栋), Zhang Kangdao (张康道), Ma Lijin (马丽锦), Zhang Qinglian (张清莲). Experimental research of heat transfer character in circulating fluidized bed [J]. Thermal Power Generation (热力发电), 2000, 1: 20-21
[10]	Ebert T A, Glichsman L R, Lints M. Determination of particle and gas convective heat transfer component in circulating fluidized bed [J]. Chemical Engineering Science, 1993, 48(12): 2179-2188
[11]	Bai Dingrong (白丁荣), Jin Yong (金涌), Yu Zhiqing (俞芷青), Cao Chunshe (曹春社). Experimental study on heat transfer between suspensions and immersed vertical surface in fast fluidized bed [J]. Journal of Chemical Industry and Engineering (China) (化工学报), 1992, 43 (4): 475-481
[12]	Yuan Z, Lu Z. Heat transfer method for solid flow rate measurement in gas-solid two phase flow [J]. Journal of Southeast University, 1997, 13 (2): 73-77
[13]	Rajan K S, Srivastava S N, Pitchumani B, et al. Thermal conductance of pneumatic conveying preheater for air-gypsum and air-sand heat transfer [J]. International Journal of Thermal Science, 2010, 49(1): 182-186
[14]	Ni Xuezi (倪学梓), Jiao Xiaoyu (焦晓渝), Wu Maolin (吴懋林), Tang Xuezhong (汤学忠), Chen Jiezhen (陈洁珍), Feng Shizhong (冯世忠). Cooling effect of particle flow furnace [J]. Metallurgical Energy (冶金能源), 1982, 7: 48-52
[15]	Botterill J S M, Teoman Y, Yuregir K R. Factors affecting heat transfer between gas-fluidized beds and immersed surfaces [J]. Powder Technology, 1984, 39 (2):177-189
[16]	Zabrodsky S S, Epanove Yu G, Galershtein D M, Saxena S C, Kolar A K. Heat transfer in a large-particle fluidized bed with immersed in-line and staggered bundles of horizontal smooth tubes[J]. International Journal of Heat and Mass Transfer, 1981, 24 (4): 571-579
[17]	Wu R L, Lim C J, Chaouki J, Grace J R. Heat transfer from a circulating fluidized bed to membrane water-wall surface [J]. AIChE Journal, 1987, 33 (11): 1888-1893
[18]	Farbar L, Morley M J. Heat transfer to flowing gas-solids mixtures in a circular tube [J]. Industrial & Engineering Chemistry, 1957, 49 (7): 1143-1150
[19]	Chen J C, Chen K L. Analysis of simultaneous radiative and conductive heat transfer in fluidized beds [J]. Chemical Engineering Communications, 1981, 9 (1-6): 255-271
[20]	Thring R H. Fluidised bed combustion for the stirling engine [J]. International Journal of Heat and Mass Transfer, 1977, 20 (9): 911-918
[21]	Basu P, Nag P K. Heat transfer to wall of a circulating fluidized-bed furnace [J]. Chemical Engineering Science, 1996, 51 (1): 1-26
[22]	Dow W M, Jakob M. Heat transfer between a vertical tube and a fluidized air-solid mixture [J]. Chemical Engineering Progress, 1951, 47 (12): 537-546
[23]	Grewal N S, Saxena S C. Heat transfer between a horizontal tube and a gas-solid fluidized bed [J]. International Journal of Heat and Mass Transfer, 1980, 23 (11): 1505-1519
[24]	Botterill J S M, Teoman Y, Yuregir K R. Temperature effects on the heat transfer behavior of gas fluidized bed [J]. AIChE Symposium Series, 1981, 77 (208): 330-337
[25]	Kalita P, Mahanta P, Saha U K. Some studies on wall-to-bed heat transfer in a pressurized circulating fluidized bed unit//5th BSME International Conference on Thermal Engineering [C]. 2013: 153-173
[26]	Olsson S E, Almstedt A E. Local instantaneous and time-averaged heat transfer in a pressurized fluidized bed with horizontal tubes: influence of pressure, fluidization velocity and tube-bank geometry [J]. Chemical Engineering Science, 1995, 50 (20): 3231-3245
[27]	Anderson B A, Johnson F, Leckner B. Heat transfer measurements in fluidized bed boiler//The 9th Int. Conference on Fluidized Bed Combusion [C]. Boston, USA, 1987: 592-598
[28]	Wu R, Lim C J, Chauki J, Grance J R. Heat transfer from a circulating fluidized bed to membrane waterwall surfaces [J]. AIChE Journal, 1987, 33 (11): 1888-1693
[29]	Wu R L, Grace J R, Lim C J. A model for heat transfer in circulating fluidized beds [J]. Chemical Engineering Science, 1990, 45 (12): 3389-3398
[30]	Wu R L, Grace J R, Lim C J, Brereton C M H. Suspension to surface heat transfer in circulating fluidized bed combustor [J]. AIChE Journal, 1989, 35 (10): 1685-1691
[31]	Nag P K, Ali Nawsher Moral M. Effect of probe size on heat transfer at the wall in circulating fluidized bed [J]. International Journal of Energy Research, 2007, 14 (9): 965-974
[32]	Mickley H S, Trilling C A. Heat transfer characteristics of fluidized beds [J]. Industrial and Engineering Chemistry, 1949, 46 (6): 1135-1147
[33]	Vreedenberg H A. Heat transfer between a fluidized bed and a horizontal tube [J]. Chemical Engineering Science, 1958, 9 (1): 52-60
[34]	Ahn G R, Han G Y. Bed-to-immersed tube heat transfer in circulating fluidized bed [J]. Journal of Chemical Engineering of Japan, 1997, 30 (3): 421-426
[35]	Levenspiel O, Walton J S. Bed-wall heat transfer in fluidized system [J]. Chemical Engineering Progress, 1952, 48 (6): 307-313
[36]	Mickley H S, Fairbanks D F. Mechanism of heat transfer to fluidized beds [J]. AIChE Journal, 1955, 1 (3): 374-384
[37]	Botterill J S M, Williams J R. The mechanism of heat transfer to gas-fluidized beds [J]. Transactions of the Institution of Chemical Engineers, 1963, 41: 217-230
[38]	Wang Li, Wu Ping, Yang Jin, Ni Xuezi. Modeling of heat transfer between a high-temperature fluidized bed and an immersed surface by a surface-particle-emulsion model [J]. Chemical Engineering Science, 2007, 62 (1/2): 503-512
[39]	Royston D. Heat transfer in the flow of solids in gas suspensions through a packed bed [J]. Industrial Engineering and Chemistry Proceeding of Design and Development, 1971, 10 (2): 145-150
[40]	Balakrishnan A R, Pei D C T. Heat transfer in gas-solid packed bed systems [J]. Industrial Engineering and Chemistry Proceeding of Design and Development, 1979, 18 (1): 30-51
[41]	Balakrishnan A R, Pei D C T. Convective heat transfer in gas-solid suspension flow through packed beds [J]. AIChE Journal, 1978, 24 (4): 613-619
[42]	Wen Dongsheng, Cong T N, He Yurong, Chen Haisheng, Ding Yulong. Heat transfer of gas-solid two-phase mixtures flowing through a packed bed [J]. Chemical Engineering Science, 2007, 62 (16): 4241-4249
[43]	Cong T N, He Yurong, Chen Haisheng, Ding Yulong, Wen Dongsheng. Heat transfer of gas-solid two-phase mixtures flowing through a packed bed under constant wall heat flux conditions [J]. Chemical Engineering Journal, 2007, 130 (1): 1-10
[44]	Ergun S. Fluid flow through packed columns [J]. Chemical Engineering Process, 1952, 48: 89-94
[45]	Eisfeld B, Schnitzlein K. The influence of confining walls on the pressure drop in packed beds [J]. Chemical Engineering Science, 2001, 56 (14): 4321-4329
[46]	Ding Y, Wang Z, Wen D, Ghadiri M. Hydrodynamics of gas-solid two-phase mixtures flowing upward through packed beds [J]. Powder Technology, 2005, 153 (1): 13-22
[47]	Ding Yulong, He Yurong, Cong N T, Yang Wei, Chen Haisheng. Hydrodynamics and heat transfer of gas-solid two-phase mixtures flowing through packed beds—a review [J]. Progress in Natural Science, 2008, 18 (10): 1185-1196
[48]	Wang Z L, Ding Y L, Ghadiri M. Flow of a gas-solid two-phase mixture through a packed bed [J]. Chemical Engineering Science, 2004, 59 (15): 3071-3079
[49]	Rodriguez O M H, Pécora A A B, Bizzo W A. Heat recovery from hot solid particles in a shallow fluidized bed [J]. Applied Thermal Engineering, 2002, 22 (2): 145-160
[50]	Pitie F, Zhao C Y, Baeyens J, Degreve J, Zhang H L. Circulating fluidized bed heat recovery/storage and its potential to use coated phase-change-material (PCM) particles [J]. Applied Energy, 2013, 109: 505-513
[51]	Flamant G, Gauthier, Benoit H, Sans J, Garcia R, Boissière B, Ansart R, Hemati M. Dense suspension of solid particles as a new heat transfer fluid for concentrated solar thermal plants: on-sun proof of concept [J]. Chemical Engineering Science, 2013, 102 (11): 567-576