泡沫陶瓷填料旋转填充床微观混合性能

doi:10.3969/j.issn.0438-1157.2014.08.018

化工学报 ›› 2014, Vol. 65 ›› Issue (8): 2976-2980.DOI: 10.3969/j.issn.0438-1157.2014.08.018

泡沫陶瓷填料旋转填充床微观混合性能

张文洁, 初广文, 罗勇, 向阳, 邹海魁, 陈建峰

北京化工大学教育部超重力工程研究中心, 北京 100029

收稿日期:2013-11-21 修回日期:2014-02-17 出版日期:2014-08-05 发布日期:2014-08-05
通讯作者: 陈建峰
基金资助:
国家自然科学基金项目（21176014）。

Micromixing in rotating packed bed with ceramic foam packing

ZHANG Wenjie, CHU Guangwen, LUO Yong, XIANG Yang, ZOU Haikui, CHEN Jianfeng

Research Center of the Ministry of Education for High Gravity Engineering and Technology, Beijing University of Chemical Technology, Beijing 100029, China

Received:2013-11-21 Revised:2014-02-17 Online:2014-08-05 Published:2014-08-05
Supported by:
supported by the National Natural Science Foundation of China (21176014).

摘要/Abstract

摘要： 采用碘化物-碘酸盐平行竞争反应为工作体系，以离集指数（X_S）表征微观混合性能，实验考察了物料体积流量、H⁺浓度、旋转填充床转速、物料体积流量比等对两种不同孔径的新型整体泡沫陶瓷填料旋转填充床的微观混合性能的影响。结果表明，孔径较小的泡沫陶瓷填料更利于微观混合；H⁺浓度、进料体积流量比的增加会导致X_S增加；而旋转填充床转速、进料流量的增大都可使X_S下降。在实验研究的基础上，利用团聚模型计算泡沫陶瓷填料旋转填充床微观混合时间（t_m），得到t_m范围为0.385～8.55 ms。与传统不锈钢丝网填料对比，泡沫陶瓷填料t_m最小值（0.385 ms）低于不锈钢丝网填料的t_m最小值（1.6 ms），表明泡沫陶瓷填料的微观混合性能优于传统不锈钢丝网填料。

关键词: 旋转填充床, 微观混合, 泡沫陶瓷填料, 反应, 反应器, 混合

Abstract: Two kinds of ceramic foam packing with different apertures were used in a rotating packed bed (RPB). Micromixing efficiency in the RPB was experimentally studied by a parallel competing iodide-iodate reaction system, and segregation index (X_S) was used to represent the efficiency. Effects of volumetric flow rate, concentration of H⁺, rotational speed, and volumetric flow ratio on the micromixing efficiency were investigated. Experimental results show that the ceramic foam packing with smaller aperture is better for micromixing. As concentration of H⁺ and volumetric flow ratio increase, X_S increases, while it decreases with the increase of rotational speed and fluid flow rate. The micromixing time t_m is calculated using incorporation model based on experimental results and the range of t_m of ceramic foam packing is from 0.385 ms to 8.55 ms. Compared with traditional stainless steel mesh packing, the minimum value of t_m of ceramic foam packing (0.385 ms) is much less than that of stainless steel mesh packing (1.6 ms). It means that ceramic foam packing presents better micromixing performance.

Key words: rotating packed bed, micromixing, ceramic foam packing, reaction, reactor, mixing

中图分类号:

张文洁, 初广文, 罗勇, 向阳, 邹海魁, 陈建峰. 泡沫陶瓷填料旋转填充床微观混合性能[J]. 化工学报, 2014, 65(8): 2976-2980.

ZHANG Wenjie, CHU Guangwen, LUO Yong, XIANG Yang, ZOU Haikui, CHEN Jianfeng. Micromixing in rotating packed bed with ceramic foam packing[J]. CIESC Journal, 2014, 65(8): 2976-2980.

参考文献 20

[1]	Bourne J R. Mixing and the selectivity of chemical reactions [J]. Organic Process Research & Development, 2003, 7 (4): 471-508
[2]	Pohorecki R, Ba?dyga J. The effects of micromixing and the manner of reactor feeding on precipitation in stirred tank reactors [J]. Chemical Engineering Science, 1988, 43 (8): 1949-1954
[3]	Gu Peiyun (顾培韵), Sun Jianzhong (孙建中), Pan Qinmin (潘勤敏). Characteristics of micromixing in batch stirred tank reactor [J]. Journal of Chemical Industry and Engineering (China) (化工学报), 1994, 45 (1): 106-111
[4]	Luo Peicheng (骆培成), Cheng Yi (程易), Wang Zhanwen (汪展文). Study of fast liquid-liquid micromixing using PLIF technique [J]. Journal of Chemical Industry and Engineering (China) (化工学报), 2005, 56 (12): 2089-2293
[5]	Chen Jianfeng (陈建峰). Higee Technology and Its Application-A New Technology of Reaction and Separation (超重力技术及应用--新一代反应与分离技术) [M]. Beijing: Chemical Industry Press, 2003
[6]	Yang H J, Chu G W, Xiang Y, et al. Characterization of micromixing efficiency in rotating packed beds by chemical methods [J]. Chemical Engineering Journal, 2006, 121 (2): 147-152
[7]	Yang H J, Chu G W, Zhang J W, et al. Micromixing efficiency in a rotating packed bed: experiments and simulation[J]. Industrial & Engineering Chemistry Research, 2005, 44 (20): 7730-7737
[8]	Brockmeyer J, Pizzirusso J F. Ceramic foam offers surprising properties [J]. Materials Engineering, 1988, 105 (7): 39-41
[9]	Richardson J T, Remue D, Hung J K. Properties of ceramic foam catalyst supports: mass and heat transfer [J]. Applied Catalysis A: General, 2003, 250 (2): 319-329
[10]	Fournier M C, Falk L, Villermaux J. A new parallel competing reaction system for assessing micromixing efficiency-experimental approach [J]. Chemical Engineering Science, 1996, 51 (22): 5053-5064
[11]	Villermaux J, Falk L, Fournier M C, et al. Use of parallel competing reactions to characterize micromixing efficiency//AIChE Symposium Series [C]. USA: American Institute of Chemical Engineers, 1992, 88: 6-6
[12]	Guichardon P, Falk L, Andrieu M. Experimental comparison of the iodide-iodate and the diazo coupling micromixing test reactions in stirred reactors [J]. Chemical Engineering Research and Design, 2001, 79 (8): 906-914
[13]	Sun Qian (孙倩), Chu Guangwen (初广文), Zou Haikui (邹海魁). Micromixing efficiency of an impinging stream-helical tube reactor [J]. Journal of Chemical Engineering of Chinese Universities (高校化学工程学报), 2012, 26 (4): 558-562
[14]	Yang Haijian (杨海健), Zhang Jianwen (张建文), Miao Jianrui (苗健瑞). Study on turbulent micromixing in a tubular packed bed reactor [J]. Journal of Chemical Engineering of Chinese Universities (高校化学工程学报), 2006, 20 (3): 390-394
[15]	Wang Qi'an (王琦安), Wang Jiexin (王洁欣), Yu Wen (余文). An experimental study of the micromixing efficiency in microchannel reactors [J]. Journal of Beijing University of Chemical Technology: Natural Science (北京化工大学学报：自然科学版), 2009, 36 (3) : 1-5
[16]	Fang J Z, Lee D J. Micromixing efficiency in static mixer [J]. Chemical Engineering Science, 2001, 56(12): 3797-3802
[17]	Chu Guangwen (初广文), Song Yunhua (宋云华), Chen Jianming (陈建铭). Modified expression of segregation index for iodide-iodate reaction system [J]. Journal of Chemical Industry and Engineering (China) (化工学报), 2005, 56 (10): 1856-1859
[18]	Yang Dongjie (杨东杰), Qiu Xueqing (邱学青), Pang Yuxia (庞煜霞). Hydrodynamic performance and mass transfer efficiency of foam ceramics ring packing [J]. Journal of Chemical Industry and Engineering (China) (化工学报), 2005, 56 (11): 2077-2081
[19]	Fournier M C, Falk L, Villermaux J. A new parallel competing reaction system for assessing micromixing efficiency-determination of micromixing time by a simple mixing model [J]. Chemical Engineering Science, 1996, 51 (23): 5187-5192
[20]	Bourne J R. Comments on the iodide/iodate method for characterising micromixing [J]. Chemical Engineering Journal, 2008, 140 (1): 638-641

泡沫陶瓷填料旋转填充床微观混合性能

Micromixing in rotating packed bed with ceramic foam packing

PDF (PC)

可视化

被引次数

摘要/Abstract

引用本文

使用本文

参考文献 20

相关文章 15

编辑推荐

Metrics

本文评价

[1]	程成, 段钟弟, 孙浩然, 胡海涛, 薛鸿祥. 表面微结构对析晶沉积特性影响的格子Boltzmann模拟[J]. 化工学报, 2023, 74(S1): 74-86.
[2]	陈爱强, 代艳奇, 刘悦, 刘斌, 吴翰铭. 基板温度对HFE7100液滴蒸发过程的影响研究[J]. 化工学报, 2023, 74(S1): 191-197.
[3]	谈莹莹, 刘晓庆, 王林, 黄鲤生, 李修真, 王占伟. R1150/R600a自复叠制冷循环开机动态特性实验研究[J]. 化工学报, 2023, 74(S1): 213-222.
[4]	陈杰, 林永胜, 肖恺, 杨臣, 邱挺. 胆碱基碱性离子液体催化合成仲丁醇性能研究[J]. 化工学报, 2023, 74(9): 3716-3730.
[5]	郑玉圆, 葛志伟, 韩翔宇, 王亮, 陈海生. 中高温钙基材料热化学储热的研究进展与展望[J]. 化工学报, 2023, 74(8): 3171-3192.
[6]	程小松, 殷勇高, 车春文. 不同工质在溶液除湿真空再生系统中的性能对比[J]. 化工学报, 2023, 74(8): 3494-3501.
[7]	汪尔奇, 彭书舟, 杨震, 段远源. 含HFO混合体系气液相平衡的理论模型评价[J]. 化工学报, 2023, 74(8): 3216-3225.
[8]	汪林正, 陆俞冰, 张睿智, 罗永浩. 基于分子动力学模拟的VOCs热氧化特性分析[J]. 化工学报, 2023, 74(8): 3242-3255.
[9]	张蒙蒙, 颜冬, 沈永峰, 李文翠. 电解液类型对双离子电池阴阳离子储存行为的影响[J]. 化工学报, 2023, 74(7): 3116-3126.
[10]	黄可欣, 李彤, 李桉琦, 林梅. 加装旋转叶轮T型通道流场的模态分解[J]. 化工学报, 2023, 74(7): 2848-2857.
[11]	陈吉, 洪泽, 雷昭, 凌强, 赵志刚, 彭陈辉, 崔平. 基于分子动力学的焦炭溶损反应及其机理研究[J]. 化工学报, 2023, 74(7): 2935-2946.
[12]	何晓崐, 刘锐, 薛园, 左然. MOCVD生长AlN单晶薄膜的气相和表面化学反应综述[J]. 化工学报, 2023, 74(7): 2800-2813.
[13]	张谭, 刘光, 李晋平, 孙予罕. Ru基氮还原电催化剂性能调控策略[J]. 化工学报, 2023, 74(6): 2264-2280.
[14]	杨峥豪, 何臻, 常玉龙, 靳紫恒, 江霞. 生物质快速热解下行式流化床反应器研究进展[J]. 化工学报, 2023, 74(6): 2249-2263.
[15]	周小文, 杜杰, 张战国, 许光文. 基于甲烷脉冲法的Fe₂O₃-Al₂O₃载氧体还原特性研究[J]. 化工学报, 2023, 74(6): 2611-2623.