组合表面调控液滴特性强化蒸汽冷凝传热

doi:10.11949/j.issn.0438-1157.20150390

化工学报 ›› 2015, Vol. 66 ›› Issue (10): 3826-3833.DOI: 10.11949/j.issn.0438-1157.20150390

组合表面调控液滴特性强化蒸汽冷凝传热

彭本利, 马学虎, 兰忠, 徐威, 温荣福, 白涛

大连理工大学化学工程研究所, 辽宁省化工资源清洁利用重点实验室, 辽宁大连 116024

收稿日期:2015-03-27 修回日期:2015-04-27 出版日期:2015-10-05 发布日期:2015-10-05
通讯作者: 马学虎
基金资助:
国家自然科学基金项目(51236002);高等学校博士学科点专项科研基金项目(20120041110018)。

Steam condensation heat transfer enhancement through droplet properties manipulation with hybrid surfaces

PENG Benli, MA Xuehu, LAN Zhong, XU Wei, WEN Rongfu, BAI Tao

Liaoning Provincial Key Laboratory of Clean Utilization of Chemical Resources, Institute of Chemical Engineering, Dalian University of Technology, Dalian 116024, Liaoning, China

Received:2015-03-27 Revised:2015-04-27 Online:2015-10-05 Published:2015-10-05
Supported by:
supported by the National Natural Science Foundation of China (51236002) and the Doctoral Program Foundation for Returned Scholars, Ministry of Education of China (20120041110018).

摘要/Abstract

摘要：

制备了具有不同疏水区宽度和面积分率的疏水-亲水间隔规则排列的组合表面。观测常压蒸汽在组合表面上冷凝时疏水区液滴的特性(液滴移除方式和最大液滴半径),利用格子Boltzmann方法模拟组合表面上凝液的运动。考察疏水区、亲水区宽度和表面过冷度对组合表面强化蒸汽冷凝传热的影响。利用滴状-膜状组合传热模型分析组合表面蒸汽冷凝传热性能的影响因素,并与实验结果比较。发现疏水区液滴自发地向亲水区定向迁移,精细设计的组合表面可以实现蒸汽滴状冷凝传热的强化,实验中强化因子可达1.20。疏水区宽度约为0.55 mm时组合表面的传热性能最大。表面过冷度越大,组合表面强化传热的效果越差,模型分析与实验结果吻合良好。

关键词: 凝结, 传热, 格子Boltzmann模拟, 表面, 组合传热模型, 传热强化

Abstract:

The hybrid surfaces with hydrophobic and hydrophilic regions arranged regularly and alternatively are prepared. Various widths and area fraction of the hydrophobic region are designed. The droplet properties (such as droplet drainage mode and maximum droplet radius) during steam condensation at atmospheric pressure are visualized. The motion process of condensate on hybrid surfaces is simulated by lattice Boltzmann method. The influences of the widths and surface subcooling of hydrophobic and hydrophilic region on enhancement of the steam condensation heat transfer of the hybrid surfaces are investigated. The influencing factors on the steam condensation heat transfer performance of hybrid surfaces are analyzed and calculated by hybrid condensation heat transfer model. The comparison between model and experimental results is also conducted. It is found that the droplet on the hydrophobic region can spontaneously migrate into the hydrophilic region. The dropwise condensation heat transfer of steam can be effectively enhanced by the finely designed hybrid surfaces. The enhancement factor of the heat transfer performance of the hybrid surface can approach to 1.20. When the width of the hydrophobic region is about 0.55 mm, the heat transfer performance of hybrid surface reaches the maximum. Furthermore, the effect of the heat transfer enhancement of hybrid surfaces decreases with the increase of surface subcooling. The comparison results indicate that the analytical (theoretical) results can well and conveniently predict the experimental results.

Key words: condensation, heat transfer, lattice Boltzmann simulation, surface, heat transfer model of hybrid surfaces, heat transfer enhancement

中图分类号:

O414.13

彭本利, 马学虎, 兰忠, 徐威, 温荣福, 白涛. 组合表面调控液滴特性强化蒸汽冷凝传热[J]. 化工学报, 2015, 66(10): 3826-3833.

PENG Benli, MA Xuehu, LAN Zhong, XU Wei, WEN Rongfu, BAI Tao. Steam condensation heat transfer enhancement through droplet properties manipulation with hybrid surfaces[J]. CIESC Journal, 2015, 66(10): 3826-3833.

参考文献 29

[1]	Tanasawa I, Ochiai J. Experimental study on dropwise condensation [J]. Bulletin of Japan Society of Mechanic Engineers, 1972, 16: 1184.
[2]	Yamali C, Merte J H. A theory of dropwise condensation at large subcooling including the effect of the sweeping [J]. Heat and Mass Transfer, 2002, 38: 191-202.
[3]	Rose J W. Dropwise condensation theory and experiments: a review [J]. Proceedings Institution of Mechanical Engineers, 2002, 216: 115-128.
[4]	Le Ferve E J, Rose J W. A theory of heat transfer by dropwise condensation//Proceedings of 3rd International Heat Transfer Conference[C]. 1966: 362-375.
[5]	Daniel S, Chaudhury M K, Chen J C. Fast drop movements resulting from the phase change on a gradient surface [J]. Science, 2001, 291(5504): 633-636.
[6]	Macner A M, Daniel S, Steen P H. Condensation on surface energy gradient shifts drop size distribution toward small drops [J]. Langmuir, 2014, 30: 1788-1798.
[7]	Liao Q, Shi Y, Fan Y, Zhu X, Wang H. Numerical simulations of the equilibrium shape of liquid droplets on gradient surfaces [J]. Applied Thermal Engineering, 2009, 29: 372-379.
[8]	Zhu X, Wang H, Liao Q, Ding Y D, Gu Y B. Experiments and analysis on self-motion behaviors of liquid droplets on gradient surfaces [J]. Experimental Thermal and Fluid Science, 2009, 33(6): 947-954.
[9]	Chaudhury M K, Whitesides G M. How to make water run uphill [J]. Science, 1992, 256(5063): 1539-1541.
[10]	Ma Xuehu(马学虎), Song Tianyi(宋天一), Lan Zhong(兰忠), Zhou Xingdong(周兴东). The effect of dividing surface on heat transfer characteristics of dropwise condensation [J]. The Chinese Journal of Process Engineering(过程工程学报), 2007, 7(3): 472-475.
[11]	Ma X H, Zhou X D, Lan Z, Song T Y, Ji J. Experimental investigation of enhancement of dropwise condensation heat transfer of steam-air mixture: falling droplet effect [J]. Journal of Enhanced Heat Transfer, 2007, 14: 295-305.
[12]	Yamauchi A, Kumagai S, Takeyama T. Condensation heat transfer on various dropwise-filmwise coexisting surface [J]. Heat Transfer-Japanese Research, 1986, 15: 50-64.
[13]	Kumagai S, Tanaka S, Katsuda H, Shimada R. On the enhancement of filmwise condensation heat transfer by means of the coexistence dropwise condensation sections [J]. Experimental Heat Transfer, 1991, 4: 71-82.
[14]	Grooten M H M, van der Geld C W M. Surface property effects on dropwise condensation heat transfer from flowing air-steam mixtures to promote drainage [J]. International Journal of Thermal Sciences, 2012, 54: 220-229.
[15]	Ma X H, Zhou X D, Lan Z, Li Y M, Zhang Y. Condensation heat transfer enhancement in the presence of non-condensable gas using the interfacial effect of dropwise condensation [J]. Internatinal Journal of Heat and Mass Transfer, 2008, 51(7/8): 1728-1737.
[16]	O'Neill G A, Westwater J W. Dropwise condensation of steam on electroplated silver surfaces [J]. International Journal of Heat and Mass Transfer, 1984, 27(9): 1539-1549.
[17]	Wilcox S J, Rohsenow W M. Film condensation of potassium using copper condensing block for precise wall-temperature measurement [J]. ASME Journal of Heat Transfer, 1970, 8: 359-371.
[18]	Guo J H, Wang X Y. Simulation of the two phase flow of droplet impingement on liquid film by the lattice Boltzmann method [J]. Journal of Hydrodynamics, 2012, 24(2): 292-297.
[19]	Castrejon-Pita J R, Betton E S, Kubiak K J, Wilson M C T, Hutchings I M. The dynamics of the impact and coalescence of droplets on a solid surface [J]. Biomicrofluidics, 2011, 5: 014112.
[20]	Gong S, Cheng P. Numerical investigation of droplet motion and coalescence by an improved lattice Boltzmann model for phase transitions and multiphase flows [J]. Computer & Fluids, 2012, 53: 93-104.
[21]	Attar E, Korner C. Lattice Boltzmann method for dynamic wetting problems [J]. Journal of Colloid and Interface Science, 2009, 335: 84-93.
[22]	Moradi N, Gross M, Varnik F, Zikos G, Steinbach I. Morphologies of small droplets on patterned hydrophobic substrates [J]. Modelling Simulation Material Science Engneering, 2011, 19: 045005.
[23]	Dupuis A, Yeomans J M. Dynamics of sliding drops on superhydrophobic surfaces [J]. Europhysics Letters, 2006, 75: 105-110.
[24]	Liu X L, Cheng P. Lattice Boltzmann simulation of steady laminar film condensation on a vertical hydrophilic subcooled flatplate [J]. International Journal of Heat and Mass Transfer, 2013, 62: 507-514.
[25]	Liu X L, Cheng P. Lattice Boltzmann simulation for dropwise condensation of vapor along vertical hydrophobic flat plates [J]. International Journal of Heat and Mass Transfer, 2013, 64: 1041-1052.
[26]	Briant A J, Wagner A J, Yeomans J M. Lattice Boltzmann simulations of contact line motion(I): Liquid-gas system [J]. Physical Review E, 2004, 69: 031602.
[27]	Peng B L, Wang S F, Lan Z, Xu W, Wen R F, Ma X H. Analysis of droplet jumping phenomenon with lattice Boltzmann simulation of droplet coalescence [J]. Applied Physics Letters, 2013, 102: 151601.
[28]	Peng Benli(彭本利), Lan Zhong(兰忠), Xu Wei(徐威), Wen Rongfu(温荣福), Bai Tao(白涛), Ma Xuehu(马学虎). Droplet coalescence simulation by lattice Boltzmann method and theoretical analysis of droplet jumping phenomenon [J]. Journal of Engineering Thermophysics(工程热物理学报), 2013, 34(9): 1731-1734.
[29]	Peng B L, Ma X H, Lan Z, Xu W, Wen R F. Analysis of condensation heat transfer enhancement with dropwise-filmwise hybrid surface: droplet sizes effect [J]. International Journal of Heat and Mass Transfer, 2014, 77: 785-794.

组合表面调控液滴特性强化蒸汽冷凝传热

Steam condensation heat transfer enhancement through droplet properties manipulation with hybrid surfaces

PDF (PC)

可视化

被引次数

摘要/Abstract

引用本文

使用本文

参考文献 29

相关文章 15

编辑推荐

Metrics

本文评价

[1]	吴馨, 龚建英, 靳龙, 王宇涛, 黄睿宁. 超声波激励下铝板表面液滴群输运特性的研究[J]. 化工学报, 2023, 74(S1): 104-112.
[2]	苏伟, 马东旭, 金旭, 刘忠彦, 张小松. 表面润湿性对霜层传递特性影响可视化实验研究[J]. 化工学报, 2023, 74(S1): 122-131.
[3]	张双星, 刘舫辰, 张义飞, 杜文静. R-134a脉动热管相变蓄放热实验研究[J]. 化工学报, 2023, 74(S1): 165-171.
[4]	张义飞, 刘舫辰, 张双星, 杜文静. 超临界二氧化碳用印刷电路板式换热器性能分析[J]. 化工学报, 2023, 74(S1): 183-190.
[5]	陈爱强, 代艳奇, 刘悦, 刘斌, 吴翰铭. 基板温度对HFE7100液滴蒸发过程的影响研究[J]. 化工学报, 2023, 74(S1): 191-197.
[6]	刘明栖, 吴延鹏. 导光管直径和长度对传热影响的模拟分析[J]. 化工学报, 2023, 74(S1): 206-212.
[7]	王志国, 薛孟, 董芋双, 张田震, 秦晓凯, 韩强. 基于裂隙粗糙性表征方法的地热岩体热流耦合数值模拟与分析[J]. 化工学报, 2023, 74(S1): 223-234.
[8]	晁京伟, 许嘉兴, 李廷贤. 基于无管束蒸发换热强化策略的吸附热池的供热性能研究[J]. 化工学报, 2023, 74(S1): 302-310.
[9]	程成, 段钟弟, 孙浩然, 胡海涛, 薛鸿祥. 表面微结构对析晶沉积特性影响的格子Boltzmann模拟[J]. 化工学报, 2023, 74(S1): 74-86.
[10]	李艺彤, 郭航, 陈浩, 叶芳. 催化剂非均匀分布的质子交换膜燃料电池操作条件研究[J]. 化工学报, 2023, 74(9): 3831-3840.
[11]	王玉兵, 李杰, 詹宏波, 朱光亚, 张大林. R134a在菱形离散肋微小通道内的流动沸腾换热实验研究[J]. 化工学报, 2023, 74(9): 3797-3806.
[12]	齐聪, 丁子, 余杰, 汤茂清, 梁林. 基于选择吸收纳米薄膜的太阳能温差发电特性研究[J]. 化工学报, 2023, 74(9): 3921-3930.
[13]	李科, 文键, 忻碧平. 耦合蒸气冷却屏的真空多层绝热结构对液氢储罐自增压过程的影响机制研究[J]. 化工学报, 2023, 74(9): 3786-3796.
[14]	洪瑞, 袁宝强, 杜文静. 垂直上升管内超临界二氧化碳传热恶化机理分析[J]. 化工学报, 2023, 74(8): 3309-3319.
[15]	陈天华, 刘兆轩, 韩群, 张程宾, 李文明. 喷雾冷却换热强化研究进展及影响因素[J]. 化工学报, 2023, 74(8): 3149-3170.