水平圆形与方形微小通道内R134a冷凝数值模拟

doi:10.11949/j.issn.0438-1157.20151306

化工学报 ›› 2016, Vol. 67 ›› Issue (5): 1748-1754.DOI: 10.11949/j.issn.0438-1157.20151306

水平圆形与方形微小通道内R134a冷凝数值模拟

张井志^1,2, 李蔚¹

1 浙江大学能源工程学院, 浙江杭州 310027;
2 先进航空发动机协同创新中心, 浙江杭州 310027

收稿日期:2015-08-17 修回日期:2015-11-04 出版日期:2016-05-05 发布日期:2016-05-05
通讯作者: 李蔚
基金资助:
浙江省自然科学基金项目(LZ13E060001);国家自然科学基金国际合作项目(51210011)。

Numerical simulation of condensation in horizontal circular and square minichannels using R134a

ZHANG Jingzhi^1,2, LI Wei¹

1 College of Energy Engineering, Zhejiang University, Hangzhou 310027, Zhejiang, China;
2 Collaborative Innovation Center of Advanced Aero-Engine, Hangzhou 310027, Zhejiang, China

Received:2015-08-17 Revised:2015-11-04 Online:2016-05-05 Published:2016-05-05
Supported by:
supported by the Natural Science Foundation of Zhejiang Province (LZ13E060001) and the National Natural Science Foundation of China (51210011).

摘要/Abstract

摘要：

利用数值模拟研究了水平圆形与方形微小通道内R134a的冷凝换热阻力特性,制冷剂饱和温度为320 K。结果表明:传热系数与摩擦压降梯度随着质量流量、干度的升高而升高,而干度大于0.85时,摩擦压降梯度随着干度的升高而降低。方形通道的换热与阻力均高于圆形通道,数值结果与文献冷凝换热、阻力公式吻合较好。圆形通道内冷凝液膜集聚在通道下部,而方形通道内液膜集中在角落区域。薄液膜区域所占的比例随着干度的增大而增大,方形通道内的液膜厚度要小于圆形通道,换热效果优于圆形通道。

关键词: 凝结, 微小通道, 数值模拟, 传热, 压降

Abstract:

Heat transfer and pressure drop characteristics of condensation for R134a at saturation temperature of 320 K inside horizontal circular and square minichannels were investigated numerically. The results indicated that the heat transfer coefficients and frictional pressure drop gradients increased with mass flux and vapor quality, while the pressure drops decreased with increasing vapor quality at x>0.85. Compared with the circular tube, the square channel with the same perimeter as the corresponding circular tubes can enhance heat transfer coefficients and increase the pressure losses. The numerical results agreed well with the well-known empirical correlations for condensation. A thicker liquid film was obtained at the bottom of the round tube, while the liquid film for the square channel accumulated at the bottom and the middle top of the channels at lower vapor quality. The proportion of the thinner liquid film region, which corresponded to a higher heat transfer coefficient, increased with increasing vapor quality, leading to a higher heat transfer coefficient at higher vapor quality. The liquid film thicknesses in square channels were lower than that in circular channels, thus enhancing the heat transfer.

Key words: condensation, minichannels, numerical simulation, heat transfer, pressure drop

中图分类号:

TK124

张井志, 李蔚. 水平圆形与方形微小通道内R134a冷凝数值模拟[J]. 化工学报, 2016, 67(5): 1748-1754.

ZHANG Jingzhi, LI Wei. Numerical simulation of condensation in horizontal circular and square minichannels using R134a[J]. CIESC Journal, 2016, 67(5): 1748-1754.

参考文献 21

[1]	杨英英, 李敏霞, 马一太. 水平光滑细管内R32冷凝换热的流型特性[J]. 化工学报, 2014, 65(2): 445-452. DOI: 10.3969/j.issn. 0438-1157.2014.02.011. YANG Y Y, LI M X, MA Y T. Characteristics of flow pattern for condensation heat transfer of R32 in horizontal small tube [J]. CIESC Journal, 2014, 65(2): 445-452. DOI: 10.3969/j.issn.0438-1157. 2014.02.011.
[2]	ILLÁN-GÓMEZ F, LÓPEZ-BELCHÍ A, GARCÍA-CASCALES J R, et al. Experimental two-phase heat transfer coefficient and frictional pressure drop inside mini-channels during condensation with R1234yf and R134a [J]. Int. J. Refrig., 2015, 51: 12-23.
[3]	SAKAMATAPAN K, KAEW-ON J, DALKILIC A S, et al. Condensation heat transfer characteristics of R-134a flowing inside the multiport minichannels [J]. Int. J. Heat Mass Transfer, 2013, 64(0): 976-985
[4]	LIU N, LI J M, SUN J, et al. Heat transfer and pressure drop during condensation of R152a in circular and square microchannels [J]. Exp. Therm. Fluid. Sci., 2013, 47: 60-67.
[5]	WANG H S, ROSE J W. A theory of film condensation in horizontal noncircular section microchannels [J]. J. Heat Transfer, 2005, 127(10): 1096-1105.
[6]	WANG H S, ROSE J W. Film condensation in horizontal microchannels: effect of channel shape [J]. Int. J. Therm. Sci., 2006, 45(12): 1205-1212.
[7]	WANG H S, ROSE J W. Theory of heat transfer during condensation in microchannels [J]. Int. J. Heat Mass Transfer, 2011, 54(11/12): 2525-2534.
[8]	DA RIVA E, DEL COL D. Numerical simulation of laminar liquid film condensation in a horizontal circular minichannel [J]. J. Heat Transfer, 2012, 134(5): 051019-051019.
[9]	DA RIVA E, DEL COL D, GARIMELLA S V, et al. The importance of turbulence during condensation in a horizontal circular minichannel [J]. Int. J. Heat Mass Transfer, 2012, 55(13/14): 3470-3481.
[10]	刘纳, 李俊明. R32 在水平微细圆管内凝结换热的数值模拟[J]. 化工学报, 2014, 65(11): 4246-4253. DOI: 10.1080/10407782. 2015.1081029. LIU N, LI J M. Numerical simulation of R32 condensation heat transfer in horizontal circular microchannel [J]. CIESC Journal, 2014, 65(11): 4246-4253. DOI: 10.1080/10407782.2015.1081029.
[11]	EL MGHARI H, ASBIK M, LOUAHLIA-GUALOUS H, et al. Condensation heat transfer enhancement in a horizontal non-circular microchannel [J]. Appl. Therm. Eng., 2014, 64(1/2): 358-370.
[12]	LEE W H. A pressure iteration scheme for two-phase flow modeling [J]. Multiphase Transport Fundamentals, Reactor Safety, Applications, 1980, 1: 407-431.
[13]	WEI J, PAN L, CHEN D, et al. Numerical simulation of bubble behaviors in subcooled flow boiling under swing motion [J]. Nucl. Eng. Des., 2011, 241(8): 2898-2908.
[14]	YANG Z, PENG X, YE P. Numerical and experimental investigation of two phase flow during boiling in a coiled tube [J]. Int. J. Heat Mass Transfer, 2008, 51(5): 1003-1016.
[15]	DEL COL D, BORTOLATO M, AZZOLIN M, et al. Condensation heat transfer and two-phase frictional pressure drop in a single minichannel with R1234ze(E) and other refrigerants [J]. Int. J. Refrig., 2015, 50: 87-103.
[16]	CAVALLINI A, DEL COL D, DORETTI L, et al. Condensation in horizontal smooth tubes: a new heat transfer model for heat exchanger design [J]. Heat Transf. Eng., 2006, 27(8): 31-38.
[17]	SHAH M M. An improved and extended general correlation for heat transfer during condensation in plain tubes [J]. HVAC&R Res., 2009, 15(5): 889-913.
[18]	ZHANG M, WEBB R L. Correlation of two-phase friction for refrigerants in small-diameter tubes [J]. Exp. Therm. Fluid. Sci., 2001, 25(3): 131-139.
[19]	KIM S, MUDAWAR I. Universal approach to predicting two-phase frictional pressure drop for adiabatic and condensing mini/micro-channel flows [J]. Int. J. Heat Mass Transfer, 2012, 55(11/12): 3246-3261.
[20]	LI W, WU Z. A general correlation for adiabatic two-phase pressure drop in micro/mini-channels [J]. Int. J. Heat Mass Transfer, 2010, 53(13/14): 2732-2739.
[21]	ZHANG W, HIBIKI T, MISHIMA K. Correlations of two-phase frictional pressure drop and void fraction in mini-channel [J]. Int. J. Heat Mass Transfer, 2010, 53(1/2/3): 453-465.

水平圆形与方形微小通道内R134a冷凝数值模拟

Numerical simulation of condensation in horizontal circular and square minichannels using R134a

PDF (PC)

可视化

被引次数

摘要/Abstract

引用本文

使用本文

参考文献 21

相关文章 15

编辑推荐

Metrics

本文评价

[1]	苏伟, 马东旭, 金旭, 刘忠彦, 张小松. 表面润湿性对霜层传递特性影响可视化实验研究[J]. 化工学报, 2023, 74(S1): 122-131.
[2]	叶展羽, 山訸, 徐震原. 用于太阳能蒸发的折纸式蒸发器性能仿真[J]. 化工学报, 2023, 74(S1): 132-140.
[3]	张双星, 刘舫辰, 张义飞, 杜文静. R-134a脉动热管相变蓄放热实验研究[J]. 化工学报, 2023, 74(S1): 165-171.
[4]	张义飞, 刘舫辰, 张双星, 杜文静. 超临界二氧化碳用印刷电路板式换热器性能分析[J]. 化工学报, 2023, 74(S1): 183-190.
[5]	陈爱强, 代艳奇, 刘悦, 刘斌, 吴翰铭. 基板温度对HFE7100液滴蒸发过程的影响研究[J]. 化工学报, 2023, 74(S1): 191-197.
[6]	刘明栖, 吴延鹏. 导光管直径和长度对传热影响的模拟分析[J]. 化工学报, 2023, 74(S1): 206-212.
[7]	王志国, 薛孟, 董芋双, 张田震, 秦晓凯, 韩强. 基于裂隙粗糙性表征方法的地热岩体热流耦合数值模拟与分析[J]. 化工学报, 2023, 74(S1): 223-234.
[8]	江河, 袁俊飞, 王林, 邢谷雨. 均流腔结构对微细通道内相变流动特性影响的实验研究[J]. 化工学报, 2023, 74(S1): 235-244.
[9]	宋嘉豪, 王文. 斯特林发动机与高温热管耦合运行特性研究[J]. 化工学报, 2023, 74(S1): 287-294.
[10]	张思雨, 殷勇高, 贾鹏琦, 叶威. 双U型地埋管群跨季节蓄热特性研究[J]. 化工学报, 2023, 74(S1): 295-301.
[11]	晁京伟, 许嘉兴, 李廷贤. 基于无管束蒸发换热强化策略的吸附热池的供热性能研究[J]. 化工学报, 2023, 74(S1): 302-310.
[12]	程成, 段钟弟, 孙浩然, 胡海涛, 薛鸿祥. 表面微结构对析晶沉积特性影响的格子Boltzmann模拟[J]. 化工学报, 2023, 74(S1): 74-86.
[13]	李艺彤, 郭航, 陈浩, 叶芳. 催化剂非均匀分布的质子交换膜燃料电池操作条件研究[J]. 化工学报, 2023, 74(9): 3831-3840.
[14]	王玉兵, 李杰, 詹宏波, 朱光亚, 张大林. R134a在菱形离散肋微小通道内的流动沸腾换热实验研究[J]. 化工学报, 2023, 74(9): 3797-3806.
[15]	李科, 文键, 忻碧平. 耦合蒸气冷却屏的真空多层绝热结构对液氢储罐自增压过程的影响机制研究[J]. 化工学报, 2023, 74(9): 3786-3796.