化工学报 ›› 2016, Vol. 67 ›› Issue (9): 3559-3565.DOI: 10.11949/j.issn.0438-1157.20160015

• 流体力学与传递现象 • 上一篇    下一篇

朝下沟槽结构表面池沸腾换热

钟达文, 孟继安, 李志信   

  1. 清华大学航天航空学院, 工程热物理研究所, 北京 100084
  • 收稿日期:2016-01-06 修回日期:2016-05-31 出版日期:2016-09-05 发布日期:2016-09-05
  • 通讯作者: 孟继安
  • 基金资助:

    大型先进压水堆核电站重大专项子课题项目(2011ZX06004-008);国家重点基础研究发展计划项目(2013CB228301)。

Saturated pool boiling from downward facing structured surfaces with grooves

ZHONG Dawen, MENG Ji'an, LI Zhixin   

  1. Institutes of Engineering Thermal Physics, School of Aerospace Engineering, Tsinghua University, Beijing 100084, China
  • Received:2016-01-06 Revised:2016-05-31 Online:2016-09-05 Published:2016-09-05
  • Supported by:

    supported by the National Science and Technology Major Project of China (2011ZX06004-008) and the National Basic Research Program of China (2013CB228301).

摘要:

核电站熔融物堆内滞留技术是一项关键的严重事故应对策略,该策略已被核电站广泛采用。为增强核电站压力容器下封头外表面的沸腾换热能力,实验研究了常压下朝下沟槽结构表面的池沸腾换热,测量了倾角5°、30°、45°、60°和90°下热通量随壁面过热度的变化,获得了相应倾角下的临界热通量(CHF)。与光表面相比,朝下沟槽结构表面的CHF可提高65%~90%。实验观察发现,在高热通量下朝下沟槽结构表面气泡运动形态存在蒸汽膜和波浪蒸汽层两种结构。分析表明,沸腾换热显著增强、临界热通量大幅提高的原因是沟槽结构大幅增加了换热面积同时还明显改善了表面的润湿性。

关键词: 传热, 表面, 相变, 气泡, 临界热通量, 倾角

Abstract:

In-vessel retention is a key severe accident management strategy now widely adopted by some nuclear power plants. The saturated pool boiling heat transfer coefficients and critical heat flux (CHF) were measured from downward facing structured surface with grooves in deionized water to enhance the CHF. The orientations were 5°, 30°, 45°, 60° and 90° (vertical). The results showed that the nucleate boiling heat transfer coefficients and the local CHF for structured surface with grooves were consistently higher than those for plain surface. Compared with plain surface, the CHF increase could reach 65%-90% for structured surface. The vapor blanket and wavy vapor layer bubble structures with different CHF trigger mechanisms on the downward facing surface at high heat fluxes were observed on structured surface. The enhancement of the local CHF and the nucleate boiling heat transfer coefficients was mainly due to the significantly increase of heat transfer area and the grooves that effectively improve surface wettability.

Key words: heat transfer, surface, phase change, bubble, critical heat flux, orientation

中图分类号: