蒸汽喷射器混合室两相流动的数值模拟

doi:10.11949/j.issn.0438-1157.20161644

摘要/Abstract

摘要：

应用适用于跨声速流动的湿蒸汽两相流模型对蒸汽喷射器内流体的流动进行了数值模拟研究。重点研究了蒸汽喷射器混合室内流体的流动过程，并比较了采用湿蒸汽模型和理想气体模型计算结果差异。研究结果表明，湿蒸汽模型中，蒸汽喷射器引射系数略高于理想气体模型的，混合室内喷嘴出口和引射蒸汽入口附近激波产生的局部高压明显小于理想气体模型的，工作蒸汽速度、温度的降低也要比理想气体模型的小。

关键词: 蒸汽喷射器, 混合室, 凝结, 湿蒸汽模型, 引射系数, 气液两相流, 数值模拟

Abstract:

Fluid flow in steam jet ejector was simulated by employing wet steam model for transonic flow. The study focused on fluid flow in mixing chamber of steam jet ejector and compared difference in simulation results between ideal gas and wet steam models. Higher entrainment ratio of steam jet ejector, smaller localized high pressure produced by shock waves near nozzle outlet and ejector inlet, and less reduction in velocity and temperature of primary steam were observed in wet steam model than in ideal gas model.

Key words: steam ejector, mixing chamber, condensation, wet steam model, entrainment ratio, vapor-liquid two-phase flow, numerical simulation

中图分类号:

TQ026.2

武洪强, 刘中良, 李艳霞, 付维娜, 汤永智, 石灿. 蒸汽喷射器混合室两相流动的数值模拟[J]. 化工学报, 2017, 68(7): 2696-2702.

WU Hongqiang, LIU Zhongliang, LI Yanxia, FU Weina, TANG Yongzhi, SHI Can. Two-phase flow simulation in mixing chamber of steam jet ejector[J]. CIESC Journal, 2017, 68(7): 2696-2702.

参考文献 31

[1]	Keenan J H, Neumann E P, Lustwerk F. An investigation of ejector design by analysis and experiment[J]. Applied Mechanics, 1950, 72: 299-309.
[2]	徐海涛, 桑芝富. 蒸汽喷射器喷射系数计算的热力学模型[J]. 化工学报, 2004, 55(5): 704-710.Xu H T, Sang Z F. Thermodynamic models for calculating entrainment ratio of steam-jet ejector[J]. Journal of Chemical Industry and Engineering(China), 2004, 55(5): 704-710.
[3]	王菲, 沈胜强. 新型太阳能双喷射制冷系统的可用能效率分析[J]. 化工学报, 2009, 60(3): 553-559.Wang F, Shen S Q. Exergy analysis of novel solar bi-ejector refrigeration system[J]. CIESC Journal, 2009, 60(3): 553-559.
[4]	王菲, 沈胜强. 不同制冷剂喷射制冷性能计算分析[J]. 化工学报, 2010, 61(2): 275-280. Wang F, Shen S Q. Calculation and analysis for an ejector refrigeration system with various refrigerants[J]. CIESC Journal, 2010, 61(2): 275-280.
[5]	Huang B J, Jiang C B, Hu F L. Ejector performance characteristics and design analysis of jet refrigeration system[J]. Engineering for Gas Turbines Power, 1985, 107: 792-802.
[6]	Huang B J, Chang J M. Empirical correlation for ejector design[J]. Refrigeration, 1999, 22: 379-388.
[7]	Riffat S B, Omer S A. CFD modeling and experimental investigation of an ejector refrigeration system using methanol as the working fluid[J]. Energy Research, 2001, 25: 115-128.
[8]	WANG X D, DONG J L. Numerical study on the performances of steam-jet vacuum pump at different operating conditions[J]. Vacuum, 2010, 84(11): 1341-1346.
[9]	Sriveerakul T, Aphormratana S, Chunnanond K. Performance prediction of steam ejector using computational fluid dynamics(Ⅰ): Validation of the CFD results[J]. Thermal Sciences, 2007, 46: 812-822.
[10]	季建刚, 倪海, 黎立新, 等. 蒸汽喷射压缩器的变工况特性模拟与分析[J]. 化工学报, 2008, 59(3): 557-561. Ji J G, Ni H, Li L X, et al. Performance simulation and analysis of steam ejector under different operating condition[J]. Journal of Chemical Industry and Engineering(China), 2008, 59(3): 557- 561.
[11]	马昕霞, 袁益, 刘聿拯. 一种新型多喷嘴汽-液喷射器的性能[J]. 化工学报, 2011, 62(5): 1258-1263. Ma X X, Yuan Y, Liu Y Z. Performance of new type multi-nozzle steam-water ejector[J]. CIESC Journal, 2011, 62(5): 1258-1263.
[12]	Zhu Y H, Cai W J, Wen C Y, et al. Numerical investigation of geometry parameters for design of high performance ejectors[J]. Applied Thermal Engineering, 2009, 29: 898-905.
[13]	MyoungKuk J, Tony U, JuSik W, et al. CFD investigation on the flow structure inside thermo vapor compressor[J]. Energy, 2010, 35: 2694-2702.
[14]	Wu H Q, Liu Z L, Han B, et al. Numerical investigation of the influences of mixing chamber geometries on steam ejector performance[J]. Desalination, 2014, 353: 15-20.
[15]	Natthawut R, Satha A, Thanarath S. Experimental studies of a steam jet refrigeration cycle: effect of the primary nozzle geometries to system performance[J]. Experimental Thermal and Fluid Science, 2011, 35: 676-683.
[16]	沈胜强, 张琨, 刘佳, 等. 喷嘴可调式喷射器性能的实验研究[J]. 化工学报, 2009, 60(6): 1398-1401. Shen S Q, Zhang K, Liu J, et al. Experimental investigation on performance of adjustable ejector[J]. CIESC Journal, 2009, 60(6): 1398-1401.
[17]	魏晋, 唐黎明, 亓海明, 等. 混合室直径对带喷射器的跨临界CO2热泵性能影响[J]. 化工学报, 2016, 67(5): 1719-1724. Wei J, Tang L M, Qi H M, et al. Effect of mixing chamber diameter on performance of transcritical CO2 heat pump system with ejector[J]. CIESC Journal, 2016, 67 (5): 1719-1724.
[18]	沈胜强, 曲晓萍, 张博. 气-液喷射器工作参数的数值模拟[J]. 太阳能学报, 2006, 27(1): 106-110.SHEN S Q, QU X P, ZHANG B. Numerical simulation on process parameters in gas-liquid ejector[J]. Acta Energiae Solaris Sinica, 2006, 27(1): 106-110.
[19]	张军强. 蒸汽喷射凝结流动模拟研究[D]. 锦州: 辽宁工业大学, 2014.ZHANG J Q.Simulation study on steam jet condensation flow[D]. Jinzhou: Liaoning University of Technology, 2014.
[20]	Wang X D, Dong J L, Li A, et al. Numerical study of primary steam superheating effects on steam ejector flow and its pumping performance[J]. Energy, 2014, 78: 205-211.
[21]	Navid S, Masoud B, Majid S. Numerical assessment of steam nucleation on thermodynamic performance of steam ejectors[J]. Applied Thermal Engineering, 2013, 52: 449-459.
[22]	Ariafar K, Buttsworth D, Adoori G, et al. Mixing layer effects on the entrainment ratio in steam ejectors through ideal gas computational simulations[J]. Energy, 2016, 95: 380-392.
[23]	Ruangtrakoon N, Thongtip T, Aphornratana S, et al. CFD simulation on the effect of primary nozzle geometries for a steam ejector in refrigeration cycle[J]. Thermal Sciences, 2013, 63: 133-145.
[24]	Subramanian G, Natarajan S K, Adhimoulame K, et al. Comparison of numerical and experimental investigations of jet ejector with blower[J]. Thermal Sciences, 2014, 84: 134-142.
[25]	Vineet V, Chandra, Ahmed M R. Experimental and computational studies on a steam jet refrigeration system with constant area and variable area ejectors[J]. Energy Conversion and Management, 2014, 79: 377-386.
[26]	VARGS S, OLIVEURA A C, MA X L, et al. Experimental and numerical analysis of a variable area ratio steam ejector[J]. Refrigeration, 2011, 34: 1668-1675.
[27]	LI X C, WANG T, Benjamin D. Numerical analysis of the performance of a thermal ejector in a steam evaporator[J]. Applied Thermal Engineering, 2010, 30: 2708-2717.
[28]	Varga S, Oliveira A C, Diaconu B. Numerical assessment of steam ejector efficiencies using CFD[J]. Refrigeration, 2009, 32: 1203-1211.
[29]	YANG X, LONG X, YAO X. Numerical investigation on the mixing process in a steam ejector with different nozzle structures[J]. Thermal Sciences, 2012, 56: 95-106.
[30]	Sriveerakul T, Aphornratana S, Chunnanond K. Performance prediction of steam ejector using computational fluid dynamics(Ⅱ): Flow structure of a steam ejector influenced by operating pressures and geometries[J]. Thermal Sciences, 2007, 46: 823-833.
[31]	Moore M J, Walters P T. Predicting the fog drop size in wet steam turbines[C]//Proceedings of the Wet Steam 4 Conference. 1973: 37-73.