微反应器内入口结构对Taylor气泡形成过程的影响

doi:10.3969/j.issn.0438-1157.2014.03.006

CIESC Journal ›› 2014, Vol. 65 ›› Issue (3): 805-812.DOI: 10.3969/j.issn.0438-1157.2014.03.006

微反应器内入口结构对Taylor气泡形成过程的影响

党敏辉^1,2, 任明月^1,2, 陈光文¹

1 中国科学院大连化学物理研究所, 辽宁大连 116023;
2 中国科学院大学, 北京 100049

收稿日期:2013-08-12 修回日期:2013-09-25 出版日期:2014-03-05 发布日期:2014-03-05
通讯作者: 陈光文
作者简介:党敏辉（1984—），男，博士研究生。
基金资助:
国家自然科学基金项目（21225627，21106141）。

Effect of microchannel inlet configuration on Taylor bubble formation in microreactors

DANG Minhui^1,2, REN Mingyue^1,2, CHEN Guangwen¹

1 Dalian Institute of Chemical Physics, Chinese Academy of Sciences, Dalian 116023, Liaoning, China;
2 University of Chinese Academy of Sciences, Beijing 100049, China

Received:2013-08-12 Revised:2013-09-25 Online:2014-03-05 Published:2014-03-05
Supported by:
supported by the National Natural Science Foundation of China (21225627, 21106141).

摘要/Abstract

摘要： 采用计算流体力学方法，考察了微通道入口结构、气液比及两相混合速度对Taylor气泡形成过程的影响，模拟结果与可视化实验符合良好。与单纯流体体积法相比，水平集法（level set）和流体体积法（volume of fluid）相耦合的方法（coupled level set and volume of fluid method，CLSVOF）可获得更精确的气液界面，且CLSVOF法结果与实验结果更符合。数值模拟结果发现，通道入口结构及气液比对气泡长度、气泡生成频率及气泡体积有很大影响。气液比恒定，不同通道入口结构，两相混合速度对气泡长度有不同影响。

关键词: 泰勒流, 两相流, 计算流体力学, 微通道, 微反应器, 入口结构

Abstract: The effects of microchannel inlet configuration, gas-liquid flow ratio and two-phase mixture velocity on Taylor bubble formation were investigated via computational fluid dynamics (CFD) method, and the simulated values were in good agreement with the visualization experimental results. Compared with the volume of fluid method (VOF),the coupled level set and volume of fluid method (CLSVOF) could get a more accurate gas-liquid interface, and the bubbles obtained by the CLSVOF method were more consistent with the experimental measurements. The results of numerical simulation showed that microchannel inlet configuration and gas-liquid flow ratio had a great influence on bubble length, bubble generation frequency and bubble volume. For the same gas-liquid flow ratio and different inlet configurations, two-phase mixture velocity had different effects on bubble length.

Key words: Taylor flow, two-phase flow, CFD, microchannels, microreactor, inlet configuration

中图分类号:

O359.1

党敏辉, 任明月, 陈光文. 微反应器内入口结构对Taylor气泡形成过程的影响[J]. CIESC Journal, 2014, 65(3): 805-812.

DANG Minhui, REN Mingyue, CHEN Guangwen. Effect of microchannel inlet configuration on Taylor bubble formation in microreactors[J]. , 2014, 65(3): 805-812.

参考文献 28

[1]	Kashid M N, Kiwi-Minsker L. Microstructured reactors for multiphase reactions: state of the art[J]. Industrial & Engineering Chemistry Research, 2009, 48(14): 6465-6485
[2]	Chen Guangwen (陈光文), Zhao Yuchao (赵玉潮), Yue Jun (乐军), Dong Zhengya (董正亚), Cao Haishan (曹海山), Yuan Quan (袁权). Transport phenomena in micro-chemical engineering[J]. CIESC Journal(化工学报), 2013, 64(1): 63-75
[3]	Luo Guangsheng (骆广生), Wang Kai (王凯), Lü Yangcheng (吕阳成), Wang Yujun (王玉军), Xu Jianhong (徐建鸿). Research and development of micro-scale multiphase reaction processes[J]. CIESC Journal(化工学报), 2013, 64(1): 165-172
[4]	Chen G W, Yue J, Yuan Q. Gas-liquid microreaction technology: recent developments and future challenges[J]. Chinese Journal of Chemical Engineering, 2008, 16(5): 663-669
[5]	Cabeza V S, Kuhn S, Kulkarni A A, Jensen K F. Size-controlled flow synthesis of gold nanoparticles using a segmented flow microfluidic platform[J]. Langmuir, 2012, 28(17): 7007-7013
[6]	Yen Brian K H, Günther A, Schmidt M A, Jensen K F, Bawendi M G. A microfabricated gas-liquid segmented flow reactor for high-temperature synthesis: the case of cdse quantum dots[J]. Angewandte Chemie International Edition, 2005, 44(34): 5447-5451
[7]	Yasukawa T, Ninomiya W, Ooyachi K, Aoki N, Mae K. Enhanced production of ethyl pyruvate using gas-liquid slug flow in microchannel[J]. Chemical Engineering Journal, 2011, 167(2/3): 527-530
[8]	Bakker J J W, Zieverink M M P, Reintjens R, Kapteijn F, Moulijn J A, Kreutzer M T. Heterogeneously catalyzed continuous-flow hydrogenation using segmented flow in capillary columns[J]. Chemcatchem, 2011, 3(7): 1155-1157
[9]	Ye C B, Chen G W, Yuan Q. Process characteristics of CO2 absorption by aqueous monoethanola mine in a microchannel reactor[J]. Chinese Journal of Chemical Engineering, 2012, 20(1): 111-119
[10]	Ye C B, Dang M H, Yao C Q, Chen G W, Yuan Q. Process analysis on CO2 absorption by monoethanolamine solutions in microchannel reactors[J]. Chemical Engineering Journal, 2013, 225: 120-127
[11]	Thulasidas T C, Abraham M A, Cerro R L. Dispersion during bubble-train flow in capillaries[J]. Chemical Engineering Science, 1999, 54(1): 61-76
[12]	Van Baten J M, Krishna R. CFD simulations of wall mass transfer for Taylor flow in circular capillaries[J]. Chemical Engineering Science, 2005, 60(4): 1117-1126
[13]	Shao N, Salman W, Gavriilidis A, Angeli P. CFD simulations of the effect of inlet conditions on Taylor flow formation[J]. International Journal of Heat and Fluid Flow, 2008, 29(6): 1603-1611
[14]	Yuan Xigang (袁希钢), Song Wenqi (宋文琦). Numerical simulation of gas-liquid two-phase flow pattern in T-junction microchannel[J]. Journal of Tianjin University (天津大学学报), 2012, 45(9): 763-769
[15]	Fu T T, Ma Y G, Funfschilling D, Li H Z. Bubble formation and breakup mechanism in a microfluidic flow-focusing device[J]. Chemical Engineering Science, 2009, 64(10): 2392-2400
[16]	Yue J, Luo L A, Gonthier Y, Chen G W, Yuan Q. An experimental study of air-water Taylor flow and mass transfer inside square microchannels[J]. Chemical Engineering Science, 2009, 64(16): 3697-3708
[17]	Dang Minhui, Yue Jun, Chen Guangwen, Yuan Quan. Formation characteristics of Taylor bubbles in a microchannel with a converging shape mixing junction[J]. Chemical Engineering Journal, 2013, 223(0): 99-109
[18]	Qian D Y, Lawal A. Numerical study on gas and liquid slugs for Taylor flow in a T-junction microchannel[J]. Chemical Engineering Science, 2006, 61(23): 7609-7625
[19]	Kumar V, Vashisth S, Hoarau Y, Nigam K D P. Slug flow in curved microreactors: hydrodynamic study[J]. Chemical Engineering Science, 2007, 62(24): 7494-7504
[20]	Zhao Y, Hemminger O, Fan L S. Experiment and lattice Boltzmann simulation of two-phase gas-liquid flows in microchannels[J]. Chemical Engineering Science, 2007, 62(24): 7172-7183
[21]	Tan J, Li S W, Wang K, Luo G S. Gas-liquid flow in T-junction microfluidic devices with a new perpendicular rupturing flow route[J]. Chemical Engineering Journal, 2009, 146(3): 428-433
[22]	Hou Jingxin (侯璟鑫), Qian Gang (钱刚), Zhou Xinggui (周兴贵). Effects of gas inlet angle and cross-section aspect ratio on Taylor bubble behavior in microchannels[J]. CIESC Journal (化工学报), 2013, 64(6): 1976-1982
[23]	Brackbill J U, Kothe D B, Zemach C. A continuum method for modeling surface tension[J]. Journal of Computational Physics, 1992, 100(2): 335-354
[24]	Wörner M. Numerical modeling of multiphase flows in microfluidics and micro process engineering: a review of methods and applications[J]. Microfluidics and Nanofluidics, 2012, 12(6): 841-886
[25]	Sussman M, Puckett E G. A coupled level set and volume-of-fluid method for computing 3D and axisymmetric incompressible two-phase flows[J]. Journal of Computational Physics, 2000, 162(2): 301-337
[26]	Chakraborty I, Biswas G, Ghoshdastidar P S. A coupled level-set and volume-of-fluid method for the buoyant rise of gas bubbles in liquids[J]. International Journal of Heat and Mass Transfer, 2013, 58(1/2): 240-259
[27]	Albadawi A, Donoghue D B, Robinson A J, Murray D B, Delauré Y M C. On the analysis of bubble growth and detachment at low capillary and bond numbers using volume of fluid and level set methods[J]. Chemical Engineering Science, 2013, 90: 77-91
[28]	Garstecki P, Fuerstman M J, Stone H A, Whitesides G M. Formation of droplets and bubbles in a microfluidic T-junction-scaling and mechanism of break-up[J]. Lab on a Chip, 2006, 6(3): 437-446

微反应器内入口结构对Taylor气泡形成过程的影响

Effect of microchannel inlet configuration on Taylor bubble formation in microreactors

PDF (PC)

可视化

被引次数

摘要/Abstract

引用本文

使用本文

参考文献 28

相关文章 15

编辑推荐

Metrics

本文评价

[1]	张思雨, 殷勇高, 贾鹏琦, 叶威. 双U型地埋管群跨季节蓄热特性研究[J]. 化工学报, 2023, 74(S1): 295-301.
[2]	肖明堃, 杨光, 黄永华, 吴静怡. 浸没孔液氧气泡动力学数值研究[J]. 化工学报, 2023, 74(S1): 87-95.
[3]	周绍华, 詹飞龙, 丁国良, 张浩, 邵艳坡, 刘艳涛, 郜哲明. 短管节流阀内流动噪声的实验研究及降噪措施[J]. 化工学报, 2023, 74(S1): 113-121.
[4]	江河, 袁俊飞, 王林, 邢谷雨. 均流腔结构对微细通道内相变流动特性影响的实验研究[J]. 化工学报, 2023, 74(S1): 235-244.
[5]	何松, 刘乔迈, 谢广烁, 王斯民, 肖娟. 高浓度水煤浆管道气膜减阻两相流模拟及代理辅助优化[J]. 化工学报, 2023, 74(9): 3766-3774.
[6]	温凯杰, 郭力, 夏诏杰, 陈建华. 一种耦合CFD与深度学习的气固快速模拟方法[J]. 化工学报, 2023, 74(9): 3775-3785.
[7]	王玉兵, 李杰, 詹宏波, 朱光亚, 张大林. R134a在菱形离散肋微小通道内的流动沸腾换热实验研究[J]. 化工学报, 2023, 74(9): 3797-3806.
[8]	袁佳琦, 刘政, 黄锐, 张乐福, 贺登辉. 泡状入流条件下旋流泵能量转换特性研究[J]. 化工学报, 2023, 74(9): 3807-3820.
[9]	高燕, 伍鹏, 尚超, 胡泽君, 陈晓东. 基于双流体喷嘴的磁性琼脂糖微球的制备及其蛋白吸附性能探究[J]. 化工学报, 2023, 74(8): 3457-3471.
[10]	汪林正, 陆俞冰, 张睿智, 罗永浩. 基于分子动力学模拟的VOCs热氧化特性分析[J]. 化工学报, 2023, 74(8): 3242-3255.
[11]	刘文竹, 云和明, 王宝雪, 胡明哲, 仲崇龙. 基于场协同和耗散的微通道拓扑优化研究[J]. 化工学报, 2023, 74(8): 3329-3341.
[12]	岳林静, 廖艺涵, 薛源, 李雪洁, 李玉星, 刘翠伟. 凹坑缺陷对厚孔板喉部空化流动特性影响研究[J]. 化工学报, 2023, 74(8): 3292-3308.
[13]	邢雷, 苗春雨, 蒋明虎, 赵立新, 李新亚. 井下微型气液旋流分离器优化设计与性能分析[J]. 化工学报, 2023, 74(8): 3394-3406.
[14]	何晓崐, 刘锐, 薛园, 左然. MOCVD生长AlN单晶薄膜的气相和表面化学反应综述[J]. 化工学报, 2023, 74(7): 2800-2813.
[15]	郭雨莹, 敬加强, 黄婉妮, 张平, 孙杰, 朱宇, 冯君炫, 陆洪江. 稠油管道水润滑减阻及压降预测模型修正[J]. 化工学报, 2023, 74(7): 2898-2907.